Wood Shop Vacuum Layout 50,Titebond Liquid Hide Glue Home Depot Data,Woodworking Ideas With Dowels Models,Bedroom Wood Work Ideas 01 - Plans Download
A few years ago I added a mini cyclone to my shop vac. Over time, the plastic lid and seals deteriorated, so I just added a new one.
The way a cyclone works is simple: you hook it up to your shop vac and collect the sawdust in a bucket rather than in the shop vac. The vacuum connects to the top port and sucks the air through the unit. The hose you use for sucking up sawdust attaches to the side-facing port.
There are a lot of advantages to collecting the sawdust before it goes into the vacuum. The most important part of a shop vac is its filter which collects the dust particles and lets clean air blow out. Shop vac filter filled with sawdust. Another benefit is being about to see how much sawdust you have collected and easily dump the bucket.
When I used just the vac, it was amazing how often I would experience no suction power only to realize that the container was completely full of sawdust.
One problem with using the mini cyclone is that it can be cumbersome and difficult to move around. My old cyclone bolted into the side of the shop vac and it was always awkward to maneuver. Another problem with this setup is my 16 gallon shop vac. So, mine was showing signs of aging, I decided to upgrade to a much smaller unit. I bought this 4 gallon vac, but still has the same horsepower. To make the shop vac and cyclone easy to move around my shop, I built a simple cart: just a basic box, really.
I started by removing all the wheels from the shop vac. The key to making this work was taking careful measurements of my the two components so they would fit tightly together without wobbling, sliding, or tipping.
I cut a hole in one end to accommodate the hose. My measurements worked out well and the two pieces fit nicely. However, the bucket is smaller than the width of the shop vac and slides side to side. To create a snug fit, I added some cleats to the floor of the cart that the bottom of the bucket can drop into.
Since the cyclone is top-heavy, I added some cleats on the top of the cart to prevent it from tipping when I pulled it from the hose. The cross brace will need to be removed whenever I need to change the filter in the vacuum. Perfect snug fit. There is not really much to these plans, and you will most likely need to modify them to fit whatever size bucket and shop vac you have. For the Shop. I value your privacy and will protect it.
I'm not good at writing conclusions, or writing at all for that matter, so I end here I guess. I'd be happy to answer any questions. I modified the circuit by replacing the original relay with a single contact relay and replaced the ohm resistor with a 40 watt light bulb. It has ran well since then, with no false triggers, but I have procrastinated updating this site.
I also added a wall switch directly across the Aprilaire current sensor to aid in shop cleanup. The switch energizes the relay to start the vacuum directly, so I can connect a 20ft hose to clean the floor.
Looking around the one that worked the best was a swimming pool skimmer. Live right I guess. The hose reaches everywhere in the shop, even the cobwebs in the corners, and standard attachments all fit. I left the valve on the other side of the room, true it's not quite as handy, but can I reach it easy this way and this lets me put the flexible vacuum hose high on the wall for the swivel path of the saw.
I also ran a dedicated outlet on the wall for the saw from the sensed circuit across the room for the other tools on the vacuum system. Again, since I only use it for one tool at a time, there is plenty of capacity of both the electrical and vacuum system.
Thanks, Steve. Steve - great idea and thanks for sharing. I've been exploring how to build one of these and the pvc Y and valves are perfect. A couple of things I did that may be of help is 1 bought a remote outlet that I can carry in my pocket and can start the vac from anywhere in the shop which is really handy at least as long as you don't take it back into the house with you : 2 check out this video for a dust collection bucket which I've found to really work well.
Maybe smaller than you'd like but may be helpful for others. Reply 4 months ago. Question 2 years ago on Introduction. Question 3 years ago. Do you feel your shop vac has enough suction to handle the length of tubing you have? I am thinking about using a 6. My run will be feet before connecting to tablesaw etc. Also I am thinking on putting vacuum in a noice preventing cabinet. Do you feel it will over heat?
I currently use the Dust Deputy atop a 5 gallon pail before going to my shop vac. I recently bought the HF 2 HP dust collector system. I really like your set-up. For a hobby wood shop, I wanted to start my shop vac with a remote.
I don't do electrical and didn't want to spend a lot of time and money on this. Amazon carries now a lot of outlets with remotes, but my shopvac is 15amps, 6. Comes with 3 separate outlets labeled 1,2,3 and a remote with 3 buttons to operate these outlets individually. Works through walls and other obstructions. The Harbor Freight link won't paste here.
Search for Indoor Wireless Remote System 3pc. Item I found this through a youtube video where the person went to HF and found a Stanley brand equivalent, but I had no luck finding that online or at HF so settled for the house brand. Anyone on this post have any input regarding DWV vs Schedule 40?
Any reason one couldn't use DWV? Reply 5 years ago. Would have used more if shop were bigger, since you only open one at a time. Thanks so much for this. Exactly what I was looking for. While I'm comfortable with electronics, I have some old X10 outlets with a remote.
I may just try that for awhile to switch on the vac. Thanks again! The ball valves work well as a vacuum seal, but once in a while they get stiff and hard to close completely. WD40 loosens them back up. Probably fine dust on the ball is the culprit. How do the costs compare? Reply 6 years ago on Introduction. The 2" PVC pipe and fittings elbows, wyes, couplings, etc.
Total cost of a PVC system would be less, and the components are available at any home improvement store. A common complaint of the 2. The 2. I will say that it is kind of neat to be able to see dust moving through the clear 2. In my opinion, it appears that the advantages of PVC stronger, seals better, easier to find parts for, less expensive, available in longer lengths are enough that it makes sense for me to go forward with PVC.
Thank you for writing this instructable! I am in the planning stage of building a basement workshop.
Triton Clamping Pocket Hole Jig 8pce Woodworking Tools Germany Ltd Tung Oil Nz 65 |
SEKS_MONYAK
23.05.2021 at 17:41:28
snayper_lubvi
23.05.2021 at 18:40:47
99999
23.05.2021 at 16:30:34
Nacnoy_Snayper
23.05.2021 at 22:40:50
KISA
23.05.2021 at 13:12:16