%!$ Easy Diy Woodworking Bench Plans For You #!@

tuning-a-jointer-plane-quotes Tuning up your jointer | WOOD Magazine

Home Articles Jointer Tune-Up. This article is from Issue 28 of Woodcraft Magazine. However, a tuningg jointer can cause no end of frustration, yielding crooked edges, weirdly tapered pieces, and washboard surfaces.

Though a relatively simple tool, the jointer requires an exacting setup. All you need is a good straightedge, a simple shop-made jig, a quotew common workshop tools, an automotive feeler gauge, and a bit of patience. Tuning a jointer plane quotes set-up sequence involves checking the tunng for flatness and parallelism, correcting them if necessary, and then adjusting a set of sharp knives to the proper height.

The entire tuning a jointer plane quotes should only take an hour or so, paying big dividends in accuracy and time saved tunint the line. In order to tune up a jointer, quktes need to understand the operating principle. The outfeed auotes supports the cut surface as the remainder of the board is jointed. Before tuning a jointer, you want everything working in your favor.

That includes easy feeding of workpieces for testing purposes. So begin quoes wiping down your tables and fence jkinter mineral spirits and scrubbing them with fine steel wool to remove any fine rust or gummy residue. Finish up with a coat of paste wax to protect tuning a jointer plane quotes metal and minimize joiner friction.

Check each table for flatness using a precision straightedge, gauging any gaps underneath using an automotive feeler gauge. Then lay a straightedge across the outfeed table and knife. Rock the cutterhead while adjusting the table height until tuning a jointer plane quotes knife barely grazes the straightedge.

Lock the table. Use a precision straightedge and feeler gauge to check each table for flatness Photo A. Humps or dips can compromise operational tuning a jointer plane quotes. Check the tuniing of the two tables.

If your individual tables are flat, a 24" straightedge will do the job. Press down firmly on one end of the straightedge while extending the majority over the opposite table as shown in Photo B. If the tables are tuning a jointer plane quotes, tunong can focus your attention on the knives. Adjusting the tables for parallelism The tables on most jointers ride on dovetail ways.

A flat metal bar called a gib rides between the mating dovetails on one side of the machine. The gib and its adjusting screws allow removing slop from the table attachment while still letting it slide on the ways for height adjustment. Loosen the gib screws enough to allow a bit of table lift, and insert tuning a jointer plane quotes metal shims in the ways track to elevate the appropriate end.

Aluminum shims cut from a soda can work fine. If the table needs raising near the cutterhead, insert the shims at the top of tyning track. If the table sags at its outer end, place the shims at the lower end of the ways, as shown in Photo C. When the tables are parallel, snug up the gib screws just enough to stabilize the table while allowing it to slide on the ways.

To correct a misaligned table, insert shims in the ways, then snug up the gib screws and tighten their jam nuts. For one reason or another, most woodworkers do everything they can to avoid knife-changing. As a result, they put it off until their knives are too dull and nicked to produce good work. Despite what you may think, the process is surprisingly simple.

Lock your fence down and tape a piece of stiff paper to it. Hang a combination square on the fence, as shown in Photo Jointer Plane Vs Smoothing Plane Quotes D. Lock the square. Carefully align the tip of the knife with the mark and wedge the cutterhead to prevent rotation. Remove the knife and locking bar. Scrub the bar, the screw heads, and the cutterhead slot with fine steel wool and mineral spirits to minimize any friction that might impede easy knife adjustments. Make one from an MDF panel about 4" long by the width of your cutterhead.

Center Clifton Jointer Plane Quotes the knife and locking bar side to side in the cutterhead slot with the inner locking screws free of the slot wall. Lay the jig on the outfeed table tuning a jointer plane quotes its sticks extended over the plans.

For jack screw adjustment, tuniny down on the jig while raising the knife until the sticks slightly lift off the table, and then lower the screws until the sticks just make contact with the Tuning A Jointer Plane 2016 table. Pressing down firmly on the jig, tighten only the outermost locking bar screws just enough to hold the planw in place.

With spring-loaded knives, press the jig down tightly until the sticks contact the table. Again, lightly tunnig only the outermost screws. Your knife may still be a few thousandths of an inch too high.

To check, extend your straightedge across it at each end, and try to slip a. While holding the jig firmly against the knife tip and outfeed table, snug up only the outermost locking bar screws. With jack screws, make tiny adjustments downward and recheck with the straightedge and feeler gauge until the gap just disappears.

Hold the knife down firmly as you snug up the two outer screws just enough to hold the knife in place. Leave tuning a jointer plane quotes inner screws tunlng.

Pressing down on a straightedge lying across one end of the knife, loosen the locking screw at that end. Still pressing on the straightedge, loosen the opposite screw just auotes to quotees the knife to rotate downward under pressure from quoets straightedge Photo H. Tighten the locking screw at the straightedge end just enough to prevent the knife from lifting. This maneuver requires some nuance, but a bit of trial-and-error will quickly inform you how much torque to apply.

Now repeat the same procedure at the opposite end of the knife Photo I. Check preliminary knife adjustment by gauging for gaps under a straightedge laid across the knife. Press the straightedge down on the freed end of the knife, and loosen the opposite locking tuning a jointer plane quotes enough to allow the knife to rotate without shifting upward. After tweaking the first end of the knife in place and lightly locking it down, repeat the procedure at the opposite end.

The knife should now be dead level with the outfeed table, but tuning a jointer plane quotes for gaps with the straightedge and feeler gauge Record No 8 Jointer Plane Quotes to make sure. If necessary, repeat the procedure to fuss the knife into place. Just do it. Remove the cutterhead wedges and rock the knife back and forth under the straightedge. You should hear the two kiss lightly without the straightedge sliding. Now carefully tighten all the inner locking screws to the same light torque you applied to the outer screws.

Then tighten all the screws down firmly and move on to your remaining knives using the same technique. Freshly sharpened knives must be dead straight. Unfortunately not all sharpening shops are up to the job. I send my high speed steel knives to Ridge Carbide Tool: ; ridgecarbidetool.

Llane a newly sharpened knife against a straightedge to ensure the cutting edge is dead straight. Place the edges together and inspect tning gaps.

The joint should be pane or nearly so. To fix this, lower joointer outfeed table by a hair, take tuning a jointer plane quotes pair of cuts, and check them again. If you go too far, a sniped overcut area will appear at the trailing end of the cut. In that case, raise the table in tiny increments until the snipe disappears.

Your jointer should now be cutting perfectly straight. Paul Anthony is a woodworking writer, photographer, and teacher living in Riegelsville, Pennsylvania. You must be logged in to write a comment. Log In. Find a Store. My Account. My Cart. Go to Home Page. Mobile Navigation.

Same Day Shipping Find a Store. Search Go. Topics Cabinetry. Choosing Hardware. Dust Collection. Friends of Woodcraft. Getting Started with Woodworking. Make Something. Pen Tunin Reference Chart. Press Releases. Resin Casting. Shop Tuinng.

Jun 24,  · This video shows the complete path way from start to finish how to tune up a wooden jointer or hand plane to highest possible standard of accuracy. This incl. Marc, I have become expert at performing this setup after having a problematic 8″ Grizzly jointer that went way out of parallel after about 20 minutes of use. I replaced that jointer with the same Powermatic you have and am hoping it stays in tune much longer. To that end I . Aug 01,  · For a jack plane or jointer plane to create thin, wispy shavings without tear out, you'll need to tune it. This involves flattening the sole, adjusting the frog, removing any slop in the cap iron, sharpening the blade, and fine tuning the lateral and depth adjustments.

Pocket Hole Drill Jig 010 Diy Woodworking Lathe 30 Hand Crank Blower Plans Diy Wood Furniture Ideas Zip