Laguna 1412 Canada 3nd,Precision Woodworking Square Uk Pdf,Mortiser For Sale Canada Youtuber - Plans On 2021
Resaw results. That exceeded my expectations. Excels at curved cuts, too. In addition to solid resaw performance, the also works well at cutting curves, as the Laguna Guides steer the blade and minimize deflection while the work piece is steered through the cut.
The project in the picture is a cutting board that I like to make by stacking two boards and cutting the pattern on a band saw. When building this design on other band saws I used to perform an additional step, where I would have to sweeten up the joints using a router with a template and guide to eliminate the gaps left where the blade would flex as it changed direction in the cut.
Using the I can go directly from the saw to the glue-up table because the guides hold the blade so solidly that there is virtually no blade deflection when the work piece changes direction during the cut. This was an unexpected bonus with the Quick blade change. The blade change process is quick and painless on the , due to the quick release lever, the nicely designed magnetic release blade guard and the easily accessible blade path.
Quality components throughout. When I first heard about the Laguna Band Saw, and the low price point, I was concerned that I would find some compromises on quality upon close inspection, but this has simply not been the case. A large surface like this on a band saw is a nice luxury as it provides enhanced stability when cutting larger pieces. I love this fence. Kudos to Laguna for incorporating fence features from their higher end band saws into the The design is simple and ingenious, allowing the fence to be positioned upright for resawing, or switched in seconds to a low profile orientation for ripping operations.
One downside; I would prefer if the fence could be slipped on and off the saw a bit more easily, but it only takes about 10 seconds to perform the necessary partial disassembly so I guess I can live with that. This underappreciated design element on a band saw is often overlooked, but I believe that this is a critical component.
These are beefy and refined, which helps absorb vibration and minimize flexing during the cut. The table tilt mechanism is controlled with convenient lever action releases that engage solidly to whatever angle is selected.
The beefy frame is heavy gauge welded steel for serious rigidity compared to cast iron which tends to flex under stress. This is key for reliable, hassle-free resawing, as the frame absorbs much of the stress from blade tensioning. Cast iron wheels. Big band saws perform better with cast iron wheels to provide stability and to power through heavy resaw cuts.
These wheels are well made and nicely balanced. Laguna did not take any shortcuts in the wheel department. Laguna guides. These upper and lower guides control the blade at 10 points using a ceramic surface. The brilliance of this design is in its simplicity. No moving parts, no maintenance required, just solid support to keep the blade cool while preventing it from wandering under pressure.
Dust collection. Resawing produces a huge volume of fine dust and it is important to corral it for health and nuisance reasons. But the dust collection results that I experienced during my tests were quite good. During one resaw test cut I forgot to turn on my dust collector before starting the cut and I immediately figured it out after cutting into the plank, as a cloud of dust appeared directly in front of my face. That gave me a good indication that the dust collection as designed is actually accomplishing its intended task pretty well.
Quick-release blade tension lever. This is a not only a great convenience for de-tensioning the blade at the end of a shop session, but also speeds up the blade changing process. The mechanism engages solidly in either position, and there is enough travel in the action that blades can be slid on and off the wheels with ease when the blade is de-tensioned.
The rack and pinion system used to raise and lower the blade guard is extremely smooth, and I am equally impressed with how rigid the this mechanism remains even when fully extended. This is one of the key attributes for maintaining good cut quality.
Halogen work light option. It is a thoughtful feature, and if you are over 40 or ever hope to be , you will really appreciate having the task lighting readily available.
Whenever I do band saw work that requires any accuracy at all, I set up a portable task light, so it will be a nice convenience to have one attached. Plus, like everything else on this saw, it looks cool. As I continue to use the saw I will provide updates if I experience any problems with the motor or anything else related to the saw.
I encountered some minor hiccups during the setup of the that I could have worked through on my own, but when I am writing a story on a stationary tool I like to get some exposure to the customer service for the company. I called in and was immediately transferred to a technician who spent a half hour on the phone with me, not only answering my questions but taking the time to explain some additional tips for band saw work.
He was extremely knowledgeable and seemed to know the pretty well in spite of the fact that it had been on the market for less than a week and I was the first customer to call in with a question. For me, this saw is a great value and was a tremendous upgrade from my previous band saw. But for my needs, and those of most hobbyist and small shop professionals, the capacity, performance and value of the Laguna are superb. Click here to cancel reply.
It seems like that this information is very helpful for people searching for bandsaw blades. There is wide range of Bandsaw blades available from various companies and I hope you guys also sharing some more information in future too. Great suggestion, Betty. I use that for almost everything. It is good for occasional resawing as well. For bigger resaw runs I use the Resaw King from Laguna.
This will be my first bandsaw! I love your review, and going out today and buy one for my basement shop. Method 2 Tension the blade as described in method 1. Page 33 Please read the following notes, as they will assist you in getting the optimum performance from your Laguna guide system.
As with the roller guide systems, the Laguna guide system will damage your blade if it is not adjusted correctly. The guide blocks must not come in contact with the teeth of the blade.
Page 34 7. When cutting gummy or green wood, the blade can become covered with resin. You will find that the surround guide system ceramic blocks remove the resin as the blade is moved through the guide blocks and keep that part of the blade clean.
Page 35 guide to obtain the correct clearance until you gain experience. Tighten the clamp screws and remove the paper. Rotate the blade by hand, ensuring that the weld of the blade does not hit the ceramic blocks, as this will cause damage. If the blade has a bad weld, dress the blade or return it to your supplier.
The blade has many of advantages such as superior surface finish to the cut, thin kerf low wood waste , can be re-sharpened, will cut hard woods and has a long life.
Page 37 Adjusting the fence Method1 1. Make a straight pencil line on the edge of a board. Feed the wood into the blade cutting next to the pencil mark. If the blade is drifting, you will have to compensate by angling the wood to keep the cut straight. Page 38 Adjusting the table rule Table rule Adjustment slot There is a rule that is fitted to the side of the table and can be used as a quick guide on the distance that the fence is from the blade.
The rule will have to be adjusted each time the fence is adjusted for drift, as this will change the distance the fence is from the blade.
Page 39 Changing the fence height 1. Loosen the clamp screws that are located on the cast bracket. Slide the aluminum fence off the cast iron bracket. Slide the aluminum fence back onto the bracket using the second slot and retighten the clamp screws. Page 40 Thickness The thicker the blade, the stiffer the blade and the straighter the cut. The thicker the band, the greater the tendency for the blade to break.
Pitch The size of the teeth. This is usually quoted in teeth per inch TPI. The larger the tooth, the faster the cut because the tooth has a large gullet and has a greater capacity to transport large amounts of sawdust through the job. Page 41 Width The dimension from the back of the blade to the front of the teeth. The wider the blade, the stiffer the blade and the straighter the cut.
This is usually called beam strength. But wide blades cannot cut small radiuses. The Laguna 1412 Canada 7th Edition narrower the blade, the more flexible the blade and the greater the tendency the blade has to wander. Page 42 With most guide systems it is recommended that the back of the blade be rounded with a stone. As the machine is supplied with Laguna ceramic guides, this is not imperative because the ceramic will round the back of the blade as it is used.
Page 43 Causes of Blade Breakage 1. Excessive blade thickness in relation to the flywheel diameter. Defective welding. Incorrect tension, particularly if the blade is over tensioned; the tension spring no longer fulfills its function.
After use it is recommended that you slacken the tension, especially overnight placing a visible notice of this operation. Page 44 without backtracking any curve that has a radius as much as or more than is shown on the chart. Page 45 How to coil a bandsaw blade Without a doubt it is more difficult to explain how to coil a bandsaw blade than it is to actually do it.
Nevertheless, below are easy-to-follow instructions on folding a blade. Method One While wearing a jacket or long-sleeved shirt and gloves, hold the blade in front of you in one large loop, with the teeth facing towards you.
Page 46 Method Two There is another variation of this that works well with small blades but simply is not possible for larger bandsaw blades, unless you're very big and strong. This method works the same as the method above, but rather than holding the blade with both hands, grasp the blade at the top while holding the bottom of the blade with your foot teeth still facing away from you.
Page 47 Method Three The steering wheel method. Start with the blade in front of you, as if you're holding a steering wheel with your hands at the 9 o'clock and 3 o'clock positions.
Simultaneously twist your left hand up and your right hand down. As the blade starts to fold, move your hands closer together while tilting your left hand to the right and your right hand to the left. Page Maintenance And Troubleshooting Maintenance and Troubleshooting All tools and machines require regular maintenance, and the bandsaw is no exception.
This section details the general maintenance and care of your bandsaw. In general, we recommend that you only use a Teflon- based lubricant on the bandsaw.
Regular oil attracts dust and dirt, and the Teflon tends to dry and has fewer tendencies to accumulate dirt and sawdust on your machine. Page 49 Replacing the drive belt Drive belt adjusting bolt Motor drive pulley Drive belt Flywheel shaft nut To replace the belts you will have to remove the lower flywheel. Loosen the motor clamp bolts and move the motor so that the tension is completely removed from the drive belt.
Page 50 Bearings All bearings are sealed for life and do not require any maintenance. If a bearing becomes faulty, replace it.
Rust The bandsaw is made from steel and cast iron. All non-painted surfaces will rust if not protected. It is recommended that the table be protected by coating with wax if the machine is not in constant use.
Page 51 machine will not stop. The machine will not stop This is a very rare occurrence, as the machine is designed to be fail-safe. If it should occur and you cannot fix the fault, seek professional assistance. I could not be more pleased with the bandsaw. The light attachment is a great addition. I have the mobile base attachment also, and it works as expected.
I bought this saw after agonizing over the other 14" saws out there. This replaced an ancient Craftsman 12" saw. Holy Cow! I should have done this years ago. I haven't used it to it's capacity yet, but this thing sure liked to resaw! Had a minor issue with one of the ceramic guides not fully seated.
Called Laguna, and they advise to heat it up and push it in. Worked like a charm. Now it's tuned, and oh my, does it resaw. I purchased this band saw less than 2 years ago. First thing I noticed was what I thought there to be too much vibration. There is no reason for one of these saws not to run smooth.
Second the ceramic guides are a poor design. They spark and tend to come out of their grooves while sawing and ruin the blade. Adjustments don't help. I have given up on the guides and will replace them with roller guides. Third, the blade doesn't stop quickly when the stop button is pressed.
I find this dangerous and should be required on all saws. Fourth, there isn't enough hp. I would recommend shopping around before purchasing this saw. Factor in after market upgrades in your budget if you buy this saw.
I would return it if I could. I got mine from Woodcroft in Orlando. Really great guys to deal with. I drove up to see the saw although I had read a lot about it I did not want to purchase it sight unseen. As luck would have it out of stock but within seven days I had one delivered. Packaging was first rate along with fit and finish.
The manual leaves something to be desired but Laguna makes up for it with their set up video on their website. Really top-notch. The blade drift was not as easy to adjust as I would have hoped but I do have it finally dial them. Plus, as noted in other reviews on different forums the bottom door gets caught up on the washer that is attached to the mobile base.
Not a big deal but certainly an annoyance. Overall I'm really pleased with the saw. The resaw king blade is a joy to work with and over all the saw is such an improvement over my year-old 14 inch Delta. I have had my saw for about a month now and have used it a lot. The set up was very easy to do alone and everything fit perfect. Tables lined up with no problems, fence was square. I have seen other reviews and some complained about fit and finish, mine was great.
It is a smooth running and quiet saw with plenty of power. Have bot used it much yet. Overall, excellent cut quality compared to the Ridgid big box store this replaces. Not bad to set up IMHO. Easily did alone. The few cuts made so far a straight and true. THe one issue is the blade tracking. Sent email to customer servicce at laguna, waiting for the response. The bade is centered on the top wheel, offset to the front on the bottom.
The blade runs back to front going top to bottom. This means the top guide when properly set up when the guide is down, pushes the blade forward when raised. So the top guide needs to be repositioned if ever moved vertically. Not a huge deal, but I'm sure I will not always remember this.
This is the best bandsaw on the market for the money period. I do my homework before I purchase anything. I have used this saw for a while now and I can attest to solid performance. I have made several angle cuts with this machine and its well thought out design. When I set up the saw It took me and my brother 5 hours to set it up including mobility kit and light kit.
We took our time with the well laid out instructions with pics were a plus. The first time I put a blade in it was kind of scary but I have since purchased an additional blade for intricate work and I can replace one in under 5 minutes.
If you are buying a saw for the name get a Powermatic If you want a saw that is Quiet and smooth get the Laguna twelve. I will take a look at Laguna products from now on when purchasing any major shop machines. The guys at the Indy Woodcraft always celebrate with you when you drive away with any new machine. They spent hours over several visits on this purchase.
Thanks for all the knowledge. Ok my last review I had just completed the assembly and not had the opportunity to cut anything.
Since then, I have used the saw numerous times and so far has cut everything I've tried without bogging down. My test cut was a piece of black walnut about 7" square, 2 ft long. Knots and all sliced right through it as fast as I could send it through. Not that I make all my cuts this was I wanted to see what the saw was capable of.
I could not believe How nice the cut was or how powerful the saw is. I guess I owe a shout out to the blade too. I'm sure the teaming the saw with the re-saw king carbide tooth blade is the paring for the saw. This is an awesome machine and my buddies at Woodcraft couldn't have been any better. Thanks guys! The overall bandsaw is fantastic the only issue which is very minor is the set up and the blade takes a while to slow down after each cut.
Fabulous band saw. I think the pros have all been mentioned. I found assembly to be pretty straight forward and honestly only referenced the instructions for the wheel base I bought for it. One thing worth mentioning is Woodcraft's phenomenal customer service.
My first band saw was damaged by the shipping company and Woodcraft had a replacement ready to go out the door in short order. Even with a back order, I got the new saw within a week. Thank you Woodcraft for amazing customer service. After having researched the various 14" bandsaws in this price range, and after seeing the positive reviews, I decided on the Laguna as my first bandsaw.
|
Unitool Digital Tape Measure Number Bench Dog Router Insert Table Cnc Machine Zone Pocket Hole Jig X1 Quiz |
SuperDetka_sexy
16.04.2021 at 18:41:15
NELLY_FURTADO
16.04.2021 at 22:49:11
asasa
16.04.2021 at 21:24:21
ESSE
16.04.2021 at 13:30:38
EzoP
16.04.2021 at 17:13:29