%!$ Easy Diy Woodworking Bench Plans For You #!@

craftsman-10-radial-arm-saw-model-113-manual Page 53 Ripping Hold Down Function ]-he hold down must be set correctly during ripping to act as barrier against the infeed side of the blade, to help keep the workpiece flat on the table, and to deflect workpiece chips. This gives you greater clearance push sticks, and allows better stability feeding the workpiece. Page 20 Bevel Lock The bevel lock is used to hold the blade at various angles to the table. The manual is craftsman 10 radial arm saw model 113 manual good condition and covers models The visibility of both the workpiece and your' fence is used as a guide.

Summary of Contents for Craftsman Page 3 additional safety instructions for radial saws support or guide the workplace, to prevent rotating slippery, antikickback pawls s,'op kick back twisting of the workpiece during operation Never "RIP" in the crosscut position. Never make Therefore, rip with the finished side down mext miter cut with Always wear safety goggles complying with ANSI t shown on Package before commencing power tool operation Safety Goggles are available at Sears retail or catalog stores unpacking Page 5 Table clamp Page 8 3.

Page 11 unpacking assernbly Position guide fence, spacer board and rear table board behind the front table board, as shown,.

Install the two table clamps in the slots provided them at the rear of the base, and tighten them securely. NOTE: life of your saw table will Page 14 6. Power Switch and Key Insert key into switch lock. This manual contains considerable data project ideas applicable to the radial saw.

Page 19 basic saw operations 2o Since the work is pushed along the fence, it must have a reasonably straight edge order make sliding contact with the fence, Also, the work must make solid contact with table, that it will wobble. Provide a straight edge, even Manuals Brands Craftsman Manuals Saw Table Of Contents.

Quick Links. Table of Contents. Save This Manual. Previous Page. Next Page. Related Manuals for Craftsman Summary of Contents for Craftsman Page 2: Table Of Contents Ripping Cutting Aides Repair Parts Page 3: Safety Safety Major Hazards This manual has safety information instructions to help users eliminate or reduce Three major hazards are associated with the risk of accidents and injuries, including: using the radial arm saw for ripping.

They 1. Severe cuts, and loss of fingers or other are outfeed zone hazard, The cause of kickback is the binding or ,0. Several conditions can cause the blade to bind or pinch. Install the guard correctly. Follow the specific instructions in the ripping and crosscutting sections to set and use the guard correctly for each type of cut.

When lowered for crosscutting, it acts as a barrier to the leading edge of the blade. Set of pawls to be lowered to the work- piece surface for ripping. They allow workpiece to pass freely from infeed to out- feed side, but help stop the kickback Page 7 Safety Safety Instructions Read and follow all safety instructions. Personal Safety Instructions 1. It means the goggles meet impact standards set by the American National Standards Institute.

Regular eye- glasses are not safety goggles. Page 8 Safety Saw Safety Instructions 1. Use guard, pawls and riving knife accord- 6. Before turning on saw, clear table of all ing to instructions.

Keep them in working objects except workpiece to be cut and nec- order. Page 9 Safety 3. Rip only workpieces longer than the diameter of the blade. Do not rip workpieces that are shorter than the diameter of the blade being used. Workpieces that extend beyond the saw table can shift, twist, rise up from the table, or fall as they are cut or afterwards. Read and follow the safety information There are several safety labels on the saw.

Refer They alert the user to hazards explained the manual for detailed explanations the manual Page Introduction Assembly Introduction In order to get the most enjoyment out of your radial saw it is important that the machine by properly assembled, adjusted, and aligned. This procedure, although not difficult, takes time; perhaps eight hours or longer for the inexperienced user.

Page 16 X in top of Stiffener legs. Install screws, washers and nuts as shown. If you mount the saw on any other Craftsman base or flat bench, make sure Elevation Crank has proper clearance rotate. Read and understand warning tag before discarding.

Page 18 Assembly Remove saw blade. Tighten carriage lock knob, located right side of ann. Loosen guard clamp screw approximately 4 turns. Pull down to loosen 3.

Rotation 4. Its is always possible to force the arm because of the Pull the yoke lock handle towards front of saw to unlock yoke. Pull forward the yoke index lever on the left side of car- riage to disengage index Page 21 Adjustments Bevel Lock Lever The purpose of the bevel lock lever is to lock the motor at any angle.

Shipping and handling. This item will ship to Taiwan , but the seller has not specified shipping options. Contact the seller - opens in a new window or tab and request a shipping method to your location.

Shipping cost cannot be calculated. Please enter a valid ZIP Code. Shipping to: Worldwide. No additional import charges at delivery! This item will be shipped through the Global Shipping Program and includes international tracking. Learn more - opens in a new window or tab. There are 1 items available. Please enter a number less than or equal to 1.

Select a valid country. Please enter 5 or 9 numbers for the ZIP Code. Domestic handling time. Taxes may be applicable at checkout. Learn more. Return policy. No returns or exchanges, but item is covered by the eBay Money Back Guarantee - opens in a new window or tab. Payment details. Payment methods. Back to home page Return to top. Back to home page. Listed in category:. Email to friends Share on Facebook - opens in a new window or tab Share on Twitter - opens in a new window or tab Share on Pinterest - opens in a new window or tab Add to Watchlist.

Image not available Photos not available for this variation. Like New: A book that looks new but has been read. Reproduced Manual Instructions.

Wood World 10 Full Extension Drawer Slides Mp3 Types Of Antique Hand Saws Manual