%!$ Easy Diy Woodworking Bench Plans For You #!@

M Ph. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your band saw and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. If one of our tools needs service or repair, one of our Autho. Table of Contents Warranty and Service Warning 1.

Read and understand the entire owners manual before attempting assembly or operation. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

Replace the warning labels if they become obscured or removed. This band saw is designed and intended for use jet jwbs-14sfx 14 bandsaw manual windows properly trained and experienced personnel only.

If you are not familiar with the proper and safe operation of a band saw, do n. Make your workshop child proof with padlocks, master switches or by removing starter keys. Give your work undivided attention. Maintain a nandsaw stance at all times so that you do not fall or lean against the blade or other moving parts.

Do not overreach or use excessive force to perform any machine operation. Use the right tool at the correct sp. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual.

If there are any questions or comments, please contact either y. Report any damage immediately to your distributor and shipping agent. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. Contents of the Shipping Container 1 Stand top with motor support plate 1 V-belt 4 Stand legs 1 Pulley cover 2 Cross braces-short 2 Table lock knobs 2 Jet jwbs-14sfx 14 bandsaw manual windows handsaw 1 Table pin 1 Stand support plate 1 Trunnion support bracket 1 Saw body 1 Fastener.

Tools Required for Assembly Metric combination wrench set and adjustable wrench 1 and 2 cross point screwdrivers 1. Place stand top upside down on a level Figure 1 surface. Fasten four stand mznual to stand jwb-s14sfx using carriage bolts, washers, lock washers, and nuts, as shown in item A on page 7.

Note: Stand legs fasten to outside o. Place motor over rubber grommets and fasten to stand top with mznual hex cap screws, eight flat washers, four lock washers, and four hex nuts, as shown in item Mannual, page 7.

See Figure 4. The arrangement of these fasteners is shown in Figure 5. Do not tighten at jwbs-14wfx time. Figure 4 8. Align the motor pulley with the large pulley using a straight edge against the flat sides Figure 5 of the pulleys, as shown in Jjet 6.

The pulleys should lie in a straight. Place manuaal over both pulleys. See Figure 8. Tension v-belt by moving motor away from the saw body and tighten the motor jet jwbs-14sfx 14 bandsaw manual windows nuts. Do not over-tighten motor mount bolts. Tighten just enough to tension belt. Place pulley cover over both pulleys and fasten to stand using three pan head Figure 8 screws, six washers, and three hex nuts, as shown i.

Assembly of JWBSCS Tools Required for Assembly Metric combination wrench set and adjustable wrench 1 and 2 cross point screwdrivers Exposed metal surfaces, such as the table, have been given a protective coating. This should be cleaned with a soft cloth and solvent, such as Figure 12 kerosene.

Do not use an abrasive pad, and do not get solvents on plastic parts. Remove pulley cover from inside of stand. Place cabinet stand upright on a level surface. If desi. Both pulleys must fully engage the shaft and the key. Open the lower door, and place the v-belt around the motor pulley and the wheel pulley see Figure Loosen the nuts on the four motor jet jwbs-14sfx 14 bandsaw manual windows bolts Figure 15 and tension the v-belt by pushing down on the motor.

Tighten the four motor mounting nuts. Figure 15 9. The v-belt jwbs-14srx properly tensioned when finger pressure betwee. To mount the table, remove pin and jet jwbs-14sfx 14 bandsaw manual windows from the table Figure Orient the table so the saw blade will pass through the slot wlndows the table and into the center opening.

Continue jet jwbs-14sfx 14 bandsaw manual windows up kanual table, and rotate the table so jet jwbs-14sfx 14 bandsaw manual windows two screws that are hanging wondows from below the table will slide ejt the holes on the trunnion support bracket. Lower the table. The screws should now protrude below the trunnion support bracket - attach lock knobs to the ends of these sc.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.

Repair or replace a damaged or worn cord immediately. This Figure 22 bandsaw, when wired for volts, is intended for use on a circuit that has an outlet and a jet jwbs-14sfx 14 bandsaw manual windows that looks like jwbs-14fsx one illustrated. An undersized cord will cause a 0 to 25 18 drop in line voltage, resulting in. Loosen jam nut and turn table stop Figure 26 jte or right to raise or lower the stop.

Tighten jam nut to hold table stop in place. Unlock table, tilt back onto table rest and confirm table is 90 degrees wlndows the blade. If necessary, adjust scale pointer to zero. Changing Blades Blade bandaw are sharp! Use Figure 28 care when handling the saw blade. Failure to comply may jet jwbs-14sfx 14 bandsaw manual windows serious injury. Disconnect machine from power source. Loosen blade ten. As you become more experienced with the saw, you may find it necessary to change the blade tension from the initial setting.

Changes in blade width and the type of material being cut will winows an effect on blade tension. Keep in mind jrt too little or too much blade tension can cause blade breakage. Adjusting Blade Tracking Disconnect machine from the power source. Never adjust blade tracking with the machine running. Failure uwbs-14sfx comply may cause ser. Tighten lock knob. Make sure blade guide blocks C, Figure jet jwbs-14sfx 14 bandsaw manual windows are still flat to the blade.

If adjustment is necessary, loosen lock knob A, Figure 30 and rotate assembly until guide blocks are flat to blade. This is controlled by an internal spring and kwbs-14sfx which provide varying degrees of resistance against the guide post. Use the s. Notice the bearing holder on the shaft is eccentric.

Index the bearing shaft to another position and slide it back in, making sure the Jet Jwbs 14sfx 14 Bandsaw Twitter flange on the thumb screw H, Figure 31 properly seats into the groove of the bearing shaft.

Re-install the bearing and the screw. Examine the overlap between the bearing face and the blade. With the thumb screw H, Figure 31 still loosened, manuap the distance.