%!$ Easy Diy Woodworking Bench Plans For You #!@

general-finishes-gel-stain-application-guide Yes, you can mix similar products together at any ratio to make more color options. First I applied wood conditioner then applied my first coat with a paper towel thinking it would be similar process as regular wood stain. Also note that General Finishes does not recommend the use of Gel Stain over laminates or high gloss surfaces. Apply as many coats of the mix as needed to obtain the desired color, allowing hour dry time between coats. How to Choose a General finishes gel stain application guide. Note: The stain may never adhere well to buide knots because they are too dense to hold a stain.

Layering coats of gel stain per manufacturer directions , will result in a more opaque finish that is darker and shows less of the woodgrain. This type of finish looks more like paint than stain. Also, you can layer different Gel Stain Application Temperature Zip colors of gel stain, or mix different colors of gel stain, to achieve custom shades. If you have gel stain that has started to get tacky before you were able to wipe it off, dip a rag in mineral spirits and apply a little bit to the problem area. The excess gel stain should come up easily.

Once the area has dried, recoat with gel stain and wipe off within the proper timeframe. Be careful not to apply gel stain to areas where the gel stain was not removed with mineral spirits or you will create an uneven finish. For previously finished wood, yes, you need to sand before applying gel stain.

Generally, you need to sand enough to scuff up the existing finish and make the surface even. This is what makes using gel stain an advantage on previously finished wood.

For raw wood, yes, you also need to sand before applying gel stain. This will open up the grain and allow the gel stain to create an even richer and more even color. You may consider it if your wood piece, once sanded, seems uneven or damaged. The wood conditioner will not hurt anything but can only help.

I like to use fast-drying polyurethane or this performance topcoat for indoor surfaces, and Spar Urethane for outdoor surfaces like doors. Those are my top gel stain tips and tricks, and I hope they help you achieve a finish that you love!

Let me know if you have any to add. I am currently researching stains and sealants for my front door refinishing project. I have really appreciated your findings and recommendations! Thank you! Thanks so much for letting me know. Best of luck with your project! Using gel stain for the first time on floating shelves. First Gel Stain Application Temperature Key I applied wood conditioner then applied my first coat with a paper towel thinking it would be similar process as regular wood stain.

I was totally wrong about that, I know now! All four shelves are different colors and have streaks. Hi, Joanna! Before you sand them all down, you could try applying another coat of gel stain to one of the shelves to see if that evens out the colors and streaks. Wish I would have read this years ago before I started using Gel stain. I love gel stain! Have used it on Dining tables, kitchen cabinets and consoles. Yes gloves are a must! Lesson learned the hard way. Sponge brushes are best and just throw them away.

Also good to know that it should definitely be stored in the can. Used gel stain on nightstand. Not adhering properly? Dried quickly but looks the same. Both are Minwax. Please advise. I am really sorry! Gel stains, as all wood stains, were formulated to go over raw wood which has an "open" surface and can absorb some of the stain. Customers have reported the successful use of Gel products over laminate surfaces. Here are two techniques:. NOTE: When using fine wood finishes, water and spills must be wiped up in a timely fashion.

If this a high-use area near General Finishes Wood Stain Reviews a sink, consider replacing the countertop instead. If this a low-use area such as a bedroom dresser that needs a tune-up, you will be fine. Then further test the finish by duplicating normal wear and tear: washing, scrubbing, scratching, etc. General Finishes Gel Stain on knotty pine. To fix, sand the table lightly with grit sandpaper and restain the table.

Apply as many coats of the mix as needed to obtain the desired color, allowing hour dry time between coats. Note: The stain may never adhere well to the knots because they are too dense to hold a stain. You can try dry brushing the knots with the stain to deepen the color and the protecting with topcoat.

You can add more mineral spirits, but test first. The mixture will thin out quickly. Yes, but it will evaporate much more quickly so you will need to re-wet the discharge pad more frequently. Watch how to update existing finishes using a dry brush technique at this video here. Gel Topcoat is thick, while Arm-R-Seal is much thinner, and is easier to apply large projects.

Find more information about Oil Based Gel Stains here. It's always possible to darken a stained surface, but you cannot lighten a stained surface after the finish has dried.

When the surface is still wet, you can try to lighten the color by scrubbing with mineral spirits. If the finish has hardened, you will need to sand down your current stain and start over or use one of our paints. Gel Stain. If Applying General Finishes Gel Stain Effect you choose to proceed, test for adhesion on a hidden area of your project before getting started.

They are sold by manufacturers that advocate that it is ok to cover up dirt and grime, which can create a problem. GF feels that appropriate cleaning and sanding delivers a better result and saves money. If you have physical issues with the labor of sanding, at least clean the project before using a de-glosser. Rinse thoroughly. Then follow with a second scrubbing with a mix of denatured alcohol and water, also using a Scotch-Brite pad.

Let dry completely. Sand with a power sander.

Opinel Marking Knife 05 Woodworking Tools Online Shop Coupon