Chop Saw Dust Collection Systems Inc,Open Hardware Monitor Temperature 1 2 3 Ios,Wood Carving Machine 3d Touch - Reviews
A few months back I built a no fence miter saw station for my garage shop. I made a dust hood with sliding adjustable doors which makes chop saw dust collection systems inc easy to open up for mitered cuts.
Although the dust collection on this miter saw is fairly good, my shop vac filter quickly gets clogged and looses suction, which results in sawdust in the air and all over the workbench. So this is my baseline. Now I want to show you the readings when I run the saw using my regular shop vac setup. The first chop saw dust collection systems inc I want to implement is adding a dust cyclone to my shop vac. The first step is to trace and cut out the hole for the cyclone to fit onto the lid.
Chop saw dust collection systems inc cut out the circle using a utility knife, and drilled the six holes for the bolts. After lining up the gasket with the holes, I positioned the cyclone and used the provided washers and bolts to attach the cyclone to the lid. Next, I drilled a hole through my workbench using a 3 inch hole saw.
I threaded the extra hose I purchased through the hole, and hooked it up to my miter saw using a Bosch 35 mm adapter. Underneath the workbench, I connected the hoses to the dust cyclone: connect the shop vac to the top of the cyclone, and then connect the other hose the one that goes to the saw to the side of the cyclone. Just connect the saw and the vac to the indicated receptacles, and make sure to set the switch to auto. Now the shop vac will automatically turn on when the saw is activated, and will stay on for 6 seconds after the saw stops coloection clear the hose.
Totally worth it. The second solution I want to implement to improve the dust control further, is to build a dust hood behind the miter saw to trap as much dust as possible. Due to my miter saw's configuration, I needed to cut out 2 slots to make room for the knobs at the back of the fence. I positioned the rail flush up against the back of my fence. I noticed that the knobs reach right to the top of the rail.
Since, I want to make a groove where the doors will slide, this is a problem. An easy fix is to add another piece of wood to build it up. Okay, with those minor adjustments sysstems, I now want to mark out where I need to cut the groove so that the doors will slide right up against the box. I made another rail for the chop saw dust collection systems inc and cut out the same groove, and attached it, making sure that the groove lined up with the front edge of the box so the doors could slide in.
After cutting the doors, I did a few test fits and adjusted until I felt that they slid nice and smoothly. I want to be able to close the doors as much as possible so I made a chop saw dust collection systems inc cuts outs for the handle and the motor. I just eyeballed it, but you could make saq cardboard template first and then use that to cut out your door. After making a few different cuts and tests until the saw moved freely in the 90 degree position, it was time for icn air quality test to see if this dust hood makes a difference.
After a few cuts, the particle monitor lights up again, but much less than in the previous tests 6, If you icn already, be sure to check out the video. If you like my content, please subscribe to my YouTube channel. See all of my projects at diymontreal. Thank you. I have a [less chop saw dust collection systems inc miter saw and my solution so far has been to park it in a double-width door and hope most of the dust goes outside.
Your idea will be great for cold or wet weather, when the door won't be cbop or if I really need to use it somewhere else in the shop. Reply 1 year ago. Introduction: Miter Saw Dust Collection. More by the author:. I post how-to videos on my YouTube channel, as well as step-by-step tutorials on my website www. Builds include mainly woodshop project… More About diymontreal ». Seeing the the blade will hit the rail, I made eaw little notch using a Forstner bit on an angle.
Did you make this project? Share it chop saw dust collection systems inc us! I Made It! Incredible Wooden Spirals by rschoenm in Woodworking. Telescope Setting Circles by instgct in Science. Steve Tyng chp year ago. Reply Upvote. UncleEd 1 year ago on Step 8. Mikebarkley UncleEd Reply 1 year ago.
Soft Close Drawer Slides Toronto Font Home Hardware Kitchen Cabinet Drawer And Best Raspberry Pi 3 Os 55 |
AFTOSH_QAFAR_088
08.05.2021 at 11:12:32
00
08.05.2021 at 18:53:43