%!$ Easy Diy Woodworking Bench Plans For You #!@

build-your-own-poster-frame-jobs Kristin Trom Apr 27, March 11, Love the custom size frames I ordered! Think about stretching a standard 4" by 6" photo to fit a billboard - build your own poster frame jobs will look great from a couple hundred feet away but will look very blurry up close. No more! Ok, so some legit concerns about poster ow, and maybe a bit of traumatic stress from the removable wallpaper fiasco. Second, is masking tape. Design Your Frame.

I just used a rag to wipe on the stain. Wait about 10 minutes, and wipe off the stain. Let everything sit for at least 24 hours before you move on to the next step. Side Note: Do you like my formal workspace? I just used a dollar store laundry basket on the laundry room floor. Tape is my secret weapon on this project. First, use duck tape to reinforce the sides of your poster. I ran white duck tape down both edges of my poster on the back.

Second, is masking tape. This is optional depending on what type of border your poster has. I knew that my lattice pieces would end up covering some of the art, so I had to lengthen the poster. I ran masking tape along the top and bottom of the poster on both sides. This way, I could use less poster as overlap between the pieces of lattice and not have to cover any of the art.

Run craft glue along the unstained sides of the lattice. Place the two pieces together at the top and bottom of the poster. Then use clamps or a heavy object to hold the wood together until the glue dries.

I used three drill bits for this step. I started with my smallest drill bit. Then I worked my way up until the hole was big enough to fit my twine for hanging. Run rope or twine through the two drilled holes. Tie a knot, and you are ready to hang your poster. Too easy! The gray stain is perfect with the rest of my decor, and the twins love their new poster. I would have totally been saying bad words too! I love how you created this easy frame.

I am already thinking of what artwork I can frame this way. Love this. I like the idea of the duct tape on the edges on the backside to keep it from ripping. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment.

Sharing is caring! Related Posts. Chili and Cornbread Pancakes ». So it is handy to have a second set of hands for this if possible. I applied glue to one corner at a time to give me time to get everything together.

I glued each corner, and made sure to get some into the holes and inserted the dowels. Then squeezed together the best I could. You can see in the video I shared above that I started on one corner and worked Build Your Own Poster Frame Kit Youtube my way around.

Once all the dowels are started into their holes, I used long pipe clamps to help me push everything together really tight and to help make it nice and square. Once the glue was dry, I gave the corners a good sanding to get rid of any leftover glue from squeeze out, then put a Roman Ogee router bit into my router and went along the outside edges to give it a little decorative detail.

This is totally optional. You can leave your edges plain and square OR use something else besides the Roman Ogee. But side note: when routing edges like this along the outside, go counterclockwise. For more information on routers and how to use them, check out this router guide. If you think of this print as a sandwich, it would go glass in front, mat board and print in the middle, and backer board on the back side. For this, I used a rabbeting bit in my router. NOTE: route the inside edges here clockwise.

The thing about rabbeting bits Build Your Own Poster Frame Workshop is that they makes rounded corners. So I used a chisel and carefully squared my corners. OR, in hindsight, you could route these rabbets prior to assembling to avoid having to use a chisel here. Now the frame itself is finished except for actual finishing—paint, stain, poly. I polyed mine with three coats of Polycrylic.

While it was drying, I cut the mat board. The last thing that needs to be done is cut the mat board. You can buy mats in standard sizes precut at any craft store or even online. I traced out and cut the board the overall size the mat board needed to be to fit inside the rabbet from step 6.

Best Commercial Bench Vise Zone Drawer And Cabinet Locks Yamaha