%!$ Easy Diy Woodworking Bench Plans For You #!@

woodworking-plans-for-jewelry-box-10 Free Woodworking Plans for Your Home and Yard

Hey, guys! The great thing about jewrlry is that you can make them many different ways and for a ton of different purposes. The drum sander is going to allow me jewepry make custom sized stock without tearout in heavily figured wood. Seuss books. This is a great way to try out box making and you can add hinges, locks, drawers, trays, etc. Before we get started, make sure to follow me on WoodworikngFacebook jewflry, YouTube and Pinterest to keep up with all my latest builds and free projects!

Affiliate links are used on this page. See my disclosure page for info on affiliate programs. I like the ratio look on the box and this size seems to be just big enough to be substantial, but not too big. I also have jewelry box plans for beginners above so make sure to check those out. The best part is this build takes very little wood.

So you can buy nice hardwoods for the box and not break the bank. So I cut material for two boxes which you will see some parts for both boxes in the plwns. I used the maple for the sides of the box and walnut for the top, bottom, and lining for a nice contrast. I used a larger piece of walnut with some nice figure to make woodworking plans for jewelry box 10 tops and bottom panels.

I resawed the walnut into 2 pieces on the bandsaw then cut those in half to finish with 4 pieces. This is one of the best uses woodworking plans for jewelry box 10 the drum sander in my book. After they were flat I glued the pieces together into 2 panels and then cut them to size. Next, cut the grooves in the sides woodaorking the DIY jewelry box for the top and bottom panels.

Do woodworking plans for jewelry box 10 test cuts jewellry scrap before making the grooves to be sure your top and bottom panels fit snugly. By cutting the sides from the same woodworking plans for jewelry box 10 you can achieve a continuous grain flow around the whole box. Assemble the jewelry box by laying the side pieces end to end in a straight line and taping the joints on the outside.

Clamping the glue up with a web clamp makes bbox much easier, hewelry f-clamps work well also. After the box is dry sand the sides to grit before the next step.

Yes, I realize this a wooden box with no way to get inside…patience my friend. I got burning on the top edge of the jewelry box, so I took it to the drum sander to remove the burn marks and get everything level. I also did this to the underside of the top. jeweory the box in on an angle helps reduce your chances of snipe. You can also flatten the parts on a sheet of sandpaper stuck to your tablesaw.

The last piece of the jewelry box is the lining which serves as decoration as well a lip for the lid. You can miter these corners as well, but stacking miters inside miters is a woodworkiing more tricky. Glue the pieces in place and clamp with some spring clamps. Put the short pieces in first and sand everything to grit before installing.

After the glue has dried, touch up any sharp edges and do a once over of the whole jewelry box with grit sandpaper. Now apply your finish of choice. I used shellac to really pop the grain of the maple but not yellow it. I applied 4 coats and finished it with a beeswax mixture.

Even though I used some fancy wood, this simple DIY wooden jewelry box build is easy to make and a great way to get started fot box making. You jewelrh do so many more things with boxes, like splines, hinges, trays, etc.

Very nice project! I like the combination of maple and walnut. I would imagine those cuts need to be bbox precise. Thanks for the inspiration. Yup, I used the miter gauge with a wood backer and a stop block. If you bx the video you can see it in use.

And thanks! No splines to support the miter corners? Probably going to follow your design and see how it goes! I mitered the ends of my inserts and cut them so the fit woodworkiing tight.

I also chamfered the top lips woodworking plans for jewelry box 10 the woodworking plans for jewelry box 10 to about 45 degrees so that I could hinge the lid. And, those woodworking plans for jewelry box 10 panels are sweet. I Woodworking Plans For Jewelry Box Zero tried making a second woodworking plans for jewelry box 10 with store-bought oak boards I still have no planers… and my mitered corners came out all screwed up… I can only guess that when I cut them to 45 degrees on my table saw that the hardness of the oak is deflecting the blade and making my cuts really wonky.

I was trying to make a box for a foam insert wodworking go into so I needed the sides to be really precise in length and chopping at them over and over with the table saw really ruined that. But just doing one set is doable if you really take your time on setup and fitting. Glad you are getting after it! Nice job of making this nice tutorial… Wish I had your equipment…. Easily followed and you made a stunning box that anyone would be proud of….

My awesome husband made 6 of tor for Christmas presents for our adult kids this year…. Log in to leave a comment. Fix This Build That. Assemble the Simple Wooden Jewelry Box Assemble the jewelry box by laying the side pieces end to end in a straight line and taping the joints on the outside. Install the Lining on the DIY Jewelry Box The last piece of the jewelry box is the lining which serves as decoration as woorworking a lip for the lid.

Apply Woodworking plans for jewelry box 10 Finish to the Wooden Jewelry Box After the glue has dried, touch up any sharp edges and do woodworming once over of the whole jewelry box with grit sandpaper. Is there an alternative way to cut the lid for the box without a table or band saw?

Each template features a simple design and a clear face you can see where you will be routing with ease. The Q3 Template is designed for # (Solid Brass Large-Box Quadrant Hinge /8''W x /8''H x 9/32'') while the Q4 Template is designed for use with # (Solid Brass Small-Box Quadrant Hinge /4''W x /4''H x 7/32''). These free swing set plans will give you everything you need to build your children or grandchildren a swing set that they'll have fun playing on for years to come. Since you're building it yourself, you can control the cost and quality, making it likely to last for generations. To build a similar project you will need the following tools and materials: ToolList: Table Saw Stacked Dado Blade set Box Joint Jig - plans for building a shop made jig are available online (Google search) or one can be purchased ready made. Block Plane - for shaping the curved lid Electric Drill 3/4" Chisel Small Phillips head screwdriver Material list: 1/2" x 4" x 36" Oak for Box sides (for.

Titebond Genuine Hide Glue Size Dark Mahogany Wood Veneer 70