Watco Stain Zip Code,Project Report On Wood Industry Pdf,Soft Close Shelf Slides Zoom - 2021 Feature
Replacement Roller - 18". Paint Brush - 4". Industrial Concrete Floor Paint is a single component, urethane modified acrylic coating designed to be an economical way to brighten dull or stained concrete.
This extra strength polyurethane formula is recommended as interior concrete floor paint for areas with heavy foot traffic and lightweight rubber-wheeled handcarts. Excellent for general purpose use in factories, showrooms, offices, schools and workshops where the easy removal of dust, dirt, oil and grease is needed.
Not only for the indoors, it can also be used as exterior concrete floor paint for surfaces like concrete decks, walkways, curbs, and parking areas. This fast-dry, water based coating requires only minimal surface preparation, offers low odor application, and soap and water clean up.
Surface Preparation The concrete surface must be clean, dry and free of loose material. New concrete should be allowed to cure for 28 days prior to coating. Remove oil, dirt, grease and other chemical contaminants by cleaning with detergent or other suitable cleaner. Rinse thoroughly. Rinse thoroughly and allow to dry before application of the Concrete Floor Paint.
NOTE: Concrete floors on grade must be free of moisture transmission from the ground. If there is any doubt about the dryness of the concrete, conduct a test by simply taping a piece of 4 mil plastic sheet 18" by 18" on the bare concrete for 24 hours.
Be sure to tape all four sides. After 24 hours, check the concrete for signs of moisture. The concrete will be darker if damp. If moisture is found, allow additional drying time days and repeat test. Persistent moisture transmission will prevent proper performance of the coating, please contact a Watco Industrial Flooring Expert at for assistance.
Also, check for curing compound or other types of sealers by pouring a small amount of water onto the concrete. If water soaks in, the surface is suitable for coating.
If water beads Watco Stain Color Chart Code up on the concrete, the surface is not porous and a test application is warranted to ensure proper adhesion will develop. Sanding or mechanical abrading may be required if proper adhesion does not develop. Previously coated floors need to be in good sound condition with proper adhesion to the concrete substrate.
Check the adhesion of the previous coating by cutting a small X in the coating using a sharp razor knife, firmly apply a piece of 2" duct tape over the center of the X cut, then pull off with a fast snap. The coating is suitable to topcoat if no significant previous coating is removed beyond the X cut.
If the coating fails this test, then additional surface preparation is required. It is recommended previously coated floors be sanded and vacuumed prior to application of the Concrete Floor Paint. This warranty shall not apply to any Cabinet Hardware Hinges Zip Code defect or damage resulting from improper surface preparation, structural defects, failure of a previous coating or improper application of the product.
This is your sole remedy under this warranty. This warranty excludes 1 labor or costs associated with labor for the application or removal of any product, and 2 any indirect, special, incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights,and you may have other rights, which vary from state to state. Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead.
Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator NIOSH approved and proper containment and clean up. Allow stain to dry for a minimum of hours dry time may be extended due to high humidity, low temperatures, or inadequate ventilation.
DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue may spontaneously catch fire if improperly discarded. Immediately place rags, steel wool, other waste soaked with this product, and sanding residue in a sealed, water-filled, metal container. Dispose of in accordance with local fire regulations. Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection NIOSH approved or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage. For skin contact, wash thoroughly with soap and water. In case of respiratory difficulty, provide fresh air and call physician.
If swallowed, call Poison Control Center, hospital emergency room, or physician immediately. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal.
The colors shown are for reference purposes only. They have been reproduced using digital production techniques. Always test stain on a hidden area of the wood to verify desired color.
Already have an account? Login here. Spend AED more and get free shipping! It creates the rich, warm glow of a traditional hand-rubbed finish. Many projects can be completed in less than an hour - simply brush or wipe on and wipe off. Please read product labels for additional directions and precautions before using. Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
We have a 7-day return policy, which means you have 7 days after receiving your item to request a return. To be eligible for a return, your item must be in the same condition that you received it, unworn or unused, with tags, and in its original packaging. To start a return, you can contact us at sales alisuq.
Rear Mounting Brackets For Drawer Slide Key Build Your Own Twin Bed Frame 80 Jet Planes Meeting In The Air 8th |
SHEMKIREC_057
22.10.2020 at 20:30:38
kreyzi
22.10.2020 at 21:26:52
zeri
22.10.2020 at 13:13:20
NURIYEV
22.10.2020 at 23:47:32
Tenha_qizcigaz
22.10.2020 at 14:45:55