%!$ Easy Diy Woodworking Bench Plans For You #!@

trend-mortise-and-tenon-jig-guide Регулируемый шаблон используется с Trend Mortise and Tenon Jig. После настройки приспособления пользователь может просто вырезать пазы и шипы соответствующих соединений, используя те или иные комбинации резака и направляющей втулки, установленные на рутере. В каждом случае направляющая втулка следует за внутренней частью шаблона и направляет резак для получения необходимой формы. The Tenon and Mortise Jig by Trend comes with mounting hardware Trend Mortise And Tenon Jig Ebay included in the purchase. You’ll receive a setup bar with guide bush, a cutter selection chart, four F-style clamps, and seven guide bushings that will allow you to produce tenons and mortises between 1/4” to 5/8” thick. Its mainframe and plates are made of precision-cut steel with a set-up bar that will enable quick and effortless adjustment. Thanks to the screw-in guide bushes, you’ll be able to forge five different sizes of tenons and mortises. The included T-wrench will allow you to adjust the angled joint, while the clamps wi. О сервисе Прессе Авторские права Связаться с нами Авторам Рекламодателям. Fit the two Page 4 Spiral bits can be used for an improved finish. GB cutter to suit the diameter of the dowels being used. Cancel Delete. Tenon thickness min.

Different Workpiece Thicknesses. Simple jig operation. The FMT Pro routs both the mortise and matching tenon, with just one joint guide, one router bit and one jig setup.

The basic concept is simple, as shown below. The Tenon. Move the table to position the retractable sight over the layout lines. Lock the table.

Rout the tenon. Note: Duplicate tenons may now be routed without having to mark or sight the tenons. The Mortise. Clamp the mortise board to the jig with the mark aligned to the sight. Joint Fit. Slide left hand template to the right until it contacts the down stand of the set up bar. Adjust position of top plate until the down stand of the set-up bar aligns with the centre line.

Tighten levers. C bit and appropriate guide bush, lower cutter down until it touches end of timber and lock off plunge of router. Raise and lock the depth stop to the length of the tenon required. Undo bolt B. Remove the lower F clamp head. Adjust the position of the vertical guide as required. Tighten the bolt B with the hex key and refit the F clamp head. Adjust the tilting back plate to the position required.

Tighten the two side bolts with the hex key. Rout the end of the timber parallel to the top plate or cut at the appropriate angle on a snip-off saw. When narrow timbers are to be used and when the mortise is at the end of the timber, the fourth F clamp can be used to secure it. Lower cutter down until it touches end of timber and lock off plunge of router. Raise and lock the depth stop to the length of the tenon required plus 2mm. Turn each template around.

Set-up positions of top plate and templates as for round tenons. Rout in a clockwise direction following the template. Mortise The mortise is routed in the same way. GB cutter to suit the diameter of the dowels being used. Select the short or long template depending on the formation of holes to be used. Then clamp it securely using a vertical timber piece as a support. Plunge rout the holes as before.

Use the short plate for an No part of this publication may be reproduced, stored or transmitted in any form without prior permission. Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools cannot be held liable for any material rendered unusable or any form of consequential loss. Print page 1 Print document 27 pages.

Side Mount Drawer Slides Plastic File 10 Table Saw Blade For Plywood Co Woodwork Workshop Fremantle 3d