%!$ Easy Diy Woodworking Bench Plans For You #!@

rikon-belt-sander-50-114 RIKON 4" x 36" Belt / 8" Disc Combo Sander | eBay

Table Of Contents. Quick Links Download this manual. Record the serial number and date of purchase in your manual for future reference. The serial number can be found on the specification label on rikon belt sander 50-114 rear of your machine. For technical support or parts questions, email techsupport rikontools. Table of Contents.

Previous Page. Next Rikln. Page 2: Table Of Contents Changes and improvements may be made at any time, with no obligation on the part of Rikon Power Tools to modify previously rikon belt sander 50-114 units. Reasonable care has been rikon belt sander 50-114 to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety, assembly and operation of this machine.

Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. There are certain applications for which this tool was designed. DO NOT operation for which it was not designed. It will do extend yourself over the tool.

Wear oil resistant a safer and higher quality job by only performing rubber soled shoes. When using an the safe and proper operation of this product is extension cord, be sure to use one heavy enough available 50-1144 to carry the current your product will draw.

Rikon belt sander 50-114 If a properly grounded electrical receptacle is not available, an adapter as shown in FIGURE B can be used to temporarily connect this plug to a 2-contact ungrounded receptacle. The adapter has a rigid lug extending from it that MUST rikon belt sander 50-114 connected to a permanent earth ground, such as a properly grounded receptacle box.

Carefully remove all contents from the shipping carton. Compare the 50-1114 with sandeg list of contents to make sure that all of the items are accounted for, before discarding any packing material. Place parts on a protected surface for easy identification and assembly. It should be used to support workpieces in all sanding operations except inside curve sanding applications. Place the sander on a surface that is level but also provides enough room on all sides for the workpiece and for the operator.

Allow sanderr for the belt to be positioned horizontally or vertically. Using a combination square Aplace FIG. See page 13 for information on adjusting the belt frame. To adjust, please do the following: FIG. Never sand the ends of a workpiece on the idler drum, as this could cause the workpiece to fly up and result in injury. Remove the disc worktable and then FIG. See page 10 for table instructions. Replace and tighten the two screws C, D and push the tension lever E in to apply tension onto the belt.

Replace the belt rikon belt sander 50-114 support rod A back onto the machine. Push the belt by hand and check if the sanding belt tends to run to one side or the other of the two drums.

Service on this machine should only be performed by an authorized, qualified technician. For Parts under Warranty, the Serial Number of your machine is required. Page Print page 1 Print document 24 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.

Rikon 4 in. x 36 in. Belt / 8 in. Disc Sander | Dynamite Tool is a distributor pf Rikon Sanders. Browse our category for descriptions and reviews, and order yours online. Feb 20,  · The RIKON is a powerful sanding machine that features a direct drive power system driving both the disc and belt. The sanding speeds eat through wood effortlessly, while still giving the user fine control of shaping and finishing projects. Belt frame adjusts in any position from horizontal to vertical to meet your sanding www.- Rating: % positive. RIKON 4" x 36" Belt / 8" Disc Combo Sander Features and Benefits: RIKON Belt & Disc Sanders are ideal combination machines for tackling a variety of surfacing and shaping needs on projects. Taking up little space in your shop, these portable sanders can be .

Turning Stocks Into Bonds 00 Wood Project Ideas For Beginners 7th Home Cnc Machines Uk Zone Hon File Cabinet Locking Mechanism Review