%!$ Easy Diy Woodworking Bench Plans For You #!@

diy-wood-bench-2x4 33 Amazing 2x4 Wood Projects You Can Build - Girl, Just DIY!

It was definitely a labor of love but actually a lot easier than I thought it was going to be. I knew I wanted something unique above the floating bench and after tons and tons of research and brainstorming I got the perfect idea and was determined to make it come to life. Like any good project, it all started on Pinterest where I found this diy wood bench 2x4 from Bells and Whistles.

Hellllooo gorgeous. As soon as I saw it I knew this would be my inspiration. Now, I just had to figure out how to make it. I was chatting with some of my bloggy friends eiy telling them diy wood bench 2x4 idea, and one of them shared this post with me from Mandi bencb at Vintage Revivals. Goddess of all DIY. I love and follow her but bebch missed this post.

It was essentially the same concept for what I wanted to make and as I kept reading, I realized she was inspired by the same exact space, just a different photo. Then I also had them cut another piece from the same board that was the same length and about 6 inches wide. Stain your wood. This is the magic combo of stain I used for this whole project. To install the bench you want to measure up from the floor how high up the seat will be.

Make a few marks that you can connect with your level. Then we screwed a few screws into the studs. For the sides, since we were screwing into the cabinets which are laminate and not real wood we used some smaller pieces. Because the laminate di not have the strongest hold, we used some nuts and bolts to give it some extra support.

If your space was smaller and this was going to be more of a bench for show, you could just put your one piece of plywood on top of your supports and be good to go, but since this bench was actually going to be used a lot, we needed it to be strong.

We had another piece of plywood left from the board they cut for us diy wood bench 2x4 we put down first.

We put the stained piece on top of that and it was still pretty shaky and sank pretty bad in the middle. Diy wood bench 2x4 we decided to lay a couple 2x4s across it as well. We drilled those into the existing supports and then laid the stained top down.

Then we used these brackets so we would have something to screw the diy wood bench 2x4 piece into. We used four all together. Once those were screwed in, the front piece was pretty secure but we used our nail gun to shoot a couple extra nails in there on either end to make sure it stayed in place.

So if you just wanted a floating bench, there ya have it! So I had my plywood cut to the size I wanted and then had to figure out what type of wood I was going to use to make the pattern. I think I diy wood bench 2x4 in Home Depot for about 2 hours that night ha. I even had my cart loaded up with thin pieces of poplar planks that were super light weight and would have worked great. So I took those back to the shelf, and kept staring at more wood.

I ended up going with these 1x2x8 pieces of select pine. I bought 15 which was a total guess but ended up being the perfect amount. Before I started building I planned out my design in Illustrator. Honestly, I just kinda winged it and played around with different patterns. I started with the two symmetrical triangular designs on the ends and then went from there.

I printed this diy wood bench 2x4 and brought it outside with me so I had it diy wood bench 2x4 hand for easy reference. Then I got my pine boards, plywood and miter saw ready to go.

First things first was drawing two lines on the plywood marking diy wood bench 2x4 horizontal and vertical center to work from. Then I diy wood bench 2x4 the plywood. Then I started with wod triangle pattern diy wood bench 2x4 one side.

This will help give you a guide for where to cut and know what angle you need. I used a scrap piece of wood that was a littler diy wood bench 2x4 than an inch thick to measure the spacing between each board. Once this side was done, I measured each of these pieces against a new board and made pencil marks, so I could easily replicate the same design for the other side. Once I did the other side with the triangles, I placed one long board straight down the middle which gave me the perfect 24x to work off of.

Then I just started adding in the rest of the boards, using my design I created as a reference. Once you get in a groove it goes pretty quickly. I honestly had no idea how it was going to turn out.

But once I started working, I got super stoked when I realized my idea was actually going to work and it was looking really cool. I probably finished all the cuts in about two hours which was wayyy faster than I thought it was going to take. At this point nothing was glued down and I moved it into our garage to work on the next day.

Ok so the glue I used is amazing. And if you have a wood project coming up you have to use it. I discovered it at Haven this past summer and was blown away by it. It dries so fast and holds so well. I still used some small clamps along the way as I glued everything down, but only needed to leave them on there for a minute or so to make sure it bonded. I started with the frame along the outside and then did my triangles on either side and the long piece across the middle to make sure everything was centered and lined up from there.

A couple pieces ended up being a little too short or too long so I adjusted them and luckily had a couple scraps left over to make new dij. It dries super fast and it will look discolored when you stain over it. Once they were all glued, I went right into staining it. I found that using diy wood bench 2x4 couple of different sized black foam brushes was the easiest way to get into the crevices.

After some special walnut siy golden oak I gave it one coat of poly and let it dry overnight. Then it was time to bring this baby inside! It fit like a glove, diyy god. We used the 2z4 gun to put about nails into the studs. You can hardly even see them but they were just enough support to hold it up against the wall. I know that was a lot of info. Awesome Job!! Ours is in progress now. Just wondering what the measurements were on your wall piece?

Did you sand diy wood bench 2x4 you stained the back piece? It seems hard with them glued down…Also, did you wipe as you stained or just brush on without wiping off?? Hope you can help! I dyi have stained it first but I did not.

It would be easiest to stain the back first and then attach the rest of it. This is so great! When this was finished, what were the dimensions of the back piece? What size boards did you do for the side supports on the floating bench? Thanks so much! Also, adding the extra plywood and 2x4s on the bench top, how tall is the final bench top? I have literally been searching for months for inspiration thanks to you I finally have it!

Love this so much. So creative and fun. Where are the tall cabinets from? Thank you! They were actually sized wrong on a job diyy FIL was working so he got them for super cheap for me!

I followed a link on Centsational Girl and found this diy wood bench 2x4 laundry room. I love it! And this wall piece…I have to try this somewhere. Really stunning. Aw thank you so much Debbie! Duy glad you stopped diu. The wall went surprisingly quick once I got started! I have literally been drooling over this bench since the moment I saw it on your IG.

I cannot wait for my other half and I to have our own space to build this. Thank you for sharing this beauty! We really love what you have done here. Very impressive! A truly unique addition to any room.

You can build this easy and simple 2x4 garden bench. With plans, you save your time and effort. You can build a bench for your garden, patio or pavilion. The entire list of materials and tools can be purchased from your local hardware store. Overal dimension: 25(depth) x 48(width) x 36(height). Aug 30,  · Collection of DIY projects built with 2x4s. These DIY 2x4 projects are solid and inexpensive to build. Wood projects built using 2x4s for all skill levels. Build a Modern 2x4 Bench with this DIY tutorial using construction 2x4s but with a modern twist. A great project for beginners. 2x4 Wood Porch Pumpkins. Fasten a 4-in.-wide plywood straightedge to each board before ripping. Set the straightedge about 1/4 in. back from the edge of the 2x4. Don’t locate the screws too close to the ends (within 6 in.). Set the table saw fence to 4 in. and rip one edge off the board with the edge of the plywood against the fence. Repeat on each 2x4.

Wood Projects Using Cricut Company Keyhole Router Jig