%!$ Easy Diy Woodworking Bench Plans For You #!@

cutting-wood-with-utility-knife Now that the basic outlines are cut, add detail that creates the illusion cutting wood with utility knife depth and texture. Power tools are noisy, need appropriate space for setup and are a little intimidating to me. Comment from: Lyssa [Visitor]. You can make straight cuts in fiberboard with a utility knife, or use any type of power saw to do the job. Related Utilitt. The Aero Squadron Lounge -

Ted's Woodworking Plans contains complete instructions from start to finish, leaving absolutely no guesswork. Here is what you get:. A utility knife is an all-around tool that has to be maintained and cared for so it would be ready for any woodworking project.

It has to be sharp and strong and therefore must be sharpened professionally to maintain its good sharp edge. And whether you are new to woodworking or you are a professional, you will surely keep a utility knife in your person even if you are not working on a project. With proper maintenance techniques, you will have a good cutting, paring, chopping and peeling tool to use all the time.

Do you have a few tips on how to maintain a utility knife? Use the pencil lines that you ran over the edges of the top side of the board to help guide the placement of the cutting line on the underside. Lift and bend the board, then cut through the other side option 2.

Lift the board up on its side, then use your knee and hand as leverage to bend the board at a right angle, away from the existing cut line.

This is a similar process to cutting through a sheet of drywall with a utility knife. Method 2 of Mark your cuts with a pencil on the smooth side of the board.

In this case, mark your cut lines in pencil on this side and keep it facing up when you make your cuts. Run your pencil lines over the edge of the board, so you can see them when you flip the board over. Remember the old adage: measure twice, cut once! Flip the board over and use the pencil marks you ran over the edges of the board to guide you. Center a strip of masking tape over the cut line but on the opposite side of the board and stick it in place.

The tape helps protect against this. Clamp the board to a sturdy, level work surface. To reduce board vibration while cutting, lay the board on a sturdy, level workbench, with only the area you plan to cut overhanging the edge of the bench.

Limiting vibration is critical to smooth, accurate cuts with less splintering. Spring clamps—which you squeeze to open and release to tighten—and C-clamps—which you screw and unscrew to tighten and loosen—are both good choices here.

Use a carbide cutting blade and take safety precautions. This type of blade will slice right through hardboard without causing too much splintering. Along with choosing the right blade, take the time to follow all necessary safety measures as well. When using any type of power saw, wear eye protection and hearing protection, wear long sleeves, remove all dangling jewelry and clothing, and tie back any long hair.

Make each cut start-to-finish with an even pace and light pressure. A jigsaw is your best option for making curved or shaped cuts. Make sure not to press down on the saw—allow it to glide freely as it cuts.

When using a table saw , use the fence and both hands to guide the wood through the stationary, spinning blade that lifts up from the slit in the table. Work slowly and carefully, and use a pusher instead of your guide hand as it approaches the saw blade. Smooth the cut lines with medium-grit sandpaper as needed. To smooth these out, run a sheet or block of medium-grit grit sandpaper back and forth a few times over the completed cut. Method 3 of Put particle board under the marked hardboard before clamping it down.

The process for measuring, marking, and clamping down the hardboard is the same for a power saw and hand saw, with one difference. Instead of running masking tape along the underside of the cut line, sandwich a sheet of 0. See the section of this article on cutting with a power saw for more details on measuring, marking, and clamping down hardboard.

Clamp a scrap of lumber along your cut line to ensure a straight cut. To help out, use two spring clamps or C-clamps to secure a straight piece of scrap lumber right against the cut line.

This will serve as a guide to keep your cut straight. Saw a full cut through the hardboard at a steady, even pace. Hold the saw blade at a degree angle at the far edge of your cut line.

Make two small upward strokes to create a notch, then start cutting with a smooth, steady, even rhythm. Smooth them out by passing medium grit grit sandpaper over the cuts several times, then follow up with fine-grit plus grit sandpaper if needed. Include your email address to get a message when this question is answered.

Submit a Tip All tip submissions are carefully reviewed before being published. Related wikiHows How to. How to. More References 6. About This Article. Co-authored by:. Co-authors: 3. Updated: October 24, Categories: Cutting Wood. Thanks to all authors for creating a page that has been read 47, times.

Did this article help you? Yes No.

Build A Toy Car Kit Quick Is Ace Hardware Open July 4th Name Furniture Pulls 35 Inches You Carbide Woodturning Tools Ebay Uk