%!$ Easy Diy Woodworking Bench Plans For You #!@

craftsman-radial-arm-saw-key-evolution Sears | Craftsman - History | www.-

Table of Contents Section Evolition Repair Parts If within one year from the date of purchase, this Craftsman Radial Saw Guard Kit fails due to a defect in material or workmanship, Sears will repair it, free of charge.

Severe cuts, and loss of fingers or other body parts due to contact with the blade. Eye impact injuries, and blindness, from being hit by a ravial workpiece, workpiece chips or pieces of blade, 3. Bodily impact injuries, broken bones, and internal organ damage from being hit by rxdial thrown workpiece 4.

Shock or electrocution 5. Major Hazards Three major hazards are associated with using the radial arm saw for ripping, They are ouffeed zone hazard, kickback, and wrong way feed. This section only briefly explains these hazards. Read the ripping and crosscutting safety sections of your saw manual for more detailed evolutiom of these and other hazards.

Safety Symbol and Signal Words An exclamation mark inside a triangle is the safety alert symbol. If you reach around the blade to the outfeed side when ripping, and try to hold down or pull the workpiece through to complete a cut, the rotational force of the blade will pull your hand back into the blade.

Fingers will be cut off. Read and follow all safety information and instructions. When a workpiece kicks back, it could hit hard enough to cause internal organ injury, broken bones, or death. Wrong Way Feed Hazard Wrong way feed is ripping by feeding the workpiece into the outfeed side of the blade.

The rotational force of the blade can grab and pull the workpiece. Before you craftsman radial arm saw key evolution let go or pull back, the force could pull your hand along with the workpiece into the blade.

Fingers or hand could be cut off. Wrong Way Feed. Regular eyeglasses are not safety goggles. Wear close fitting clothes, short sleeved shirts, and non-slip shoes. Tie up long hair. Do not wear gloves, ties. These can Craftsman Radial Arm Saw Model 113 Key get caught in the spinning blade and pull body parts into dae blade. Wear dust mask to keep from inhaling fine particles. Wear ear protectors, use saw daily. Keep children, pets, and visitors out of work area; they could be tilt by a thrown workpiece, New Craftsman Radial Arm Saw Keyboard workpiece chips or pieces of blade.

Turn saw off, remove yellow key, and unplug before leaving work area. Do not leave until blade has stopped spinning. Make work area child-proof: remove yellow key to prevent accidental start-up; store key out of sight and reach; lock work area.

Keep floors clean and flee of sawdust, wax and other slippery materials. Keep work area well lighted and uncluttered, 6. Use saw only in dry area. Do not use in wet or damp areas. Keep them in working order. Repair or replace damaged parts before using saw. Unplug saw before doing maintenance, making adjustments, correcting alignment, or changing blades. Do not force evolktion. Use saw, blades and accessories only as intended.

Before turning on saw, clear table of all objects except workpiece to be cut and necessary fixtures, clamps, or feather-boardso. If blade jams, turn saw off immediately, remove yellow key, the free blade. Do not try to free blade with saw craftsman radial arm saw key evolution. Do not layout, assemble, or setup work with saw on, or while blade is spinning.

Keep saw table clean. Store items away from saw. Do not climb on saw or stand on saw table to reach items because saw can tip over. Cut only one workpiece at a time. Stacking or placing workpieces edge to edge can cause user to lose control of workpieceo. Safety 3. Rip only workpieces longer than the diameter of the blade.

Do not rip workpieces that are shorter craftsman radial arm saw key evolution the diameter of the blade being used. Workpieces that extend beyond the saw table can craftsman radial arm saw key evolution, twist, rise up from the table, or fall as they ar'e cut or afterwards.

Support workpiece with table extensions the same height as the saw table. To prevent tipping, support outer ends of extensions with sturdy legs or an outrigger. Do not use another person to help support workpieces or to aid by pushing or pulling on workpieces, because these actions can cause kickback.

Use table extensions. Use clamps or vice to hold workpiece. Do not overtighten blade nut because blade collar could warp 6o Do ram turn saw on and off in rapid sequence because blade can loosen. Blade should stop within 15 seconds after saw is switched off.

If blade takes longer, the saw needs repair. Contact Sears Service Center. Use only 10" or smaller diameter blades. Use blades for their recommended procedures. Keep blade sharp and Craftsman Radial Arm Saw Key 91 clean. I B Rear Table 40" Izront Fable 40" I E Tahte Supporl Handle Assembly Bag Ol Loose Parts I Conlaining: I I.

Adapter Craftsman Radial Arm Saw Key In Motor Key Bag Ol Loose Paris Assembly Guard screws, Installation existing Steps table boards. Keep all including the lev1. Remove Note: boards This retro fit guard behhM are being supplied kit requires fence, additional clearance New table. Discard the old table boards but keep the fence.

Install board. Refering to your saw owners manua! Remove the front table. The U-Clips that were used as nuts for the rear screws must be moved to the new screw location Remove them from the saw and reinstall them on zrm table. Referring to craftsman radial arm saw key evolution saw owners manual, install and level the table boards.

Remove crosscut travel may no Ionger to your saw owners tlavel. Rotate the saw to the outrip position. Dvolution and discmd ttle oflmr lmndle retaining screw, Discard tile old handle, 8.

This locks tile adapter in place. Lock motor at 0 bevel blade vertical. Position guard so riving knife fuces front of saw. Blade pinching is a cause evolytion kickback, 1. Lock yoke in in-rip position blade towards column, motor towards front of arm.

Lower arm until blade just clears table, craftsman radial arm saw key evolution. Unlock rip lock while holding up lower plastic guard, move yoke back until blade touches fence.

Craftsman radial arm saw key evolution rip craftsman radial arm saw key evolution. Lower riving knife to the table and tighten knob. The riving "knife should rest fiat against fence, 5. If adjustment is needed: 1o loosen riving knife bracket screw.

Z slide riving knife so it rests against fence. Evllution radial arm to move; locks in any desired position; pro-set indexed positions at 045L, 45R Turns motor on!

Insert into on-off craftsmsn Remove after turning saw off Move towards right to unlock, towards left to lock Support motor before unlocking because it can swing down quickly.

Jon - I purchased a Craftsman Radial Arm Saw in the late 's, but did not discover your book until about five years ago. I bought a previously owned (but nearly pristine) copy through Amazon. My copy is now well marked with highlighter and marginal notes. I have found it very valuable in keeping my saw set up for precision as well as safety. Apr 22,  · I have an old craftsman radial arm saw. Carftsman being craftsman made it do the thing will not turn on unless I have the little oval yellow two pronged safety key. I misplaced the damn thing again and this time I am sure it is gone for good. It has been two years since I used the saw and lord knows where the little yellow thing wondered off to.

Cnc Machines Winnipeg Miter Gauge Picture Frames Calculator