%!$ Easy Diy Woodworking Bench Plans For You #!@

woodworking-plans-serving-tray-quiz Tags: Tray Wooden Tray. Categories: Woodworking Plans. [yuzo_related]. Categories: B. Band Saw (20). Bending Wood (8). C. Cabinet Door Construction (20). Children’s Furniture Plans (42). Children’s Outdoor Plans (25). Circular Saw Woodworking Plans Serving Tray Rose (16). Clamp and Clamping (18). D. Door Construction (15). Drawer Construction (19). Drill (12). I have drawn plans for many of the woodworking projects on this website. Each of these plans has an accompanying article showing the actual construction of the project. Most of these woodworking plans were drawn in Sketchup, a free 3D CAD program. For most plans, the SketchUp model is included, so you can check out different views of the projects and parts. Free plans. Includes plans for trays, wind chimes and many more.  Build a simple yet useful tray to clean up those crumbs. It can be made in a short amount of time. Select a hard wood like maple or walnut and it will give you many years of service. Read more Indoor Mailbox. Always losing the mail once you bring it in the house? With just 2 simple steps you could have your own indoor mailbox.

We may receive a commission when you use our affiliate links. However, this does not impact our recommendations. The cool-looking corner joints are woodworking plans serving tray quiz to make on the tablesaw, thanks to a simple miter gauge jig and a couple of fences.

Shop-made routing sleds allow you to template-rout the arched ends, rounded cutouts and curvy handles on the router table. Forstner bit to establish the curved ends of the handle cutouts.

Cut the blanks for the sides, ends and handles Woodworking plans serving tray quiz. A, Parts A through C. Set your miter gauge 28 degrees from perpendicular at either 62 degrees or 28 degrees, depending on how your miter gauge is calibrated and attach a long fence.

Then miter one end of all your end blanks A. Use this marked blank to install a stop block on your fence so you can miter the other end of the blanks Photo 1. Cut the dadoes Fig. A, Detail 1 with a dado set and a woodworking plans serving tray quiz that holds the end piece on its beveled edge Photo 2. To make the jig, attach a tall fence to your miter gauge and fasten two of your extra mitered pieces to the fence.

A, Detail 2. The bevel angle is the same as that on the mitered ends. To get a smoothly sawn surface, make two beveling passes. Then reset the fence and make a light clean-up pass to final width. Set up the saw to cut the half-lap tenons on the sides. You have to remove the blade guard for this procedure, so be careful. Install the dado set and lower it below the saw table. Then make a sacrificial fence to house the dado set, so you can crosscut woodworking plans serving tray quiz tenons to length Photo 4.

Setting the blade height to cut the cheeks and bottom faces of the tenons is fussy, because the tenons have to fit just right. Use the dadoes on one of the end pieces to mark the location of the tenons on an extra side piece. Cut the back face of the tenon last. The last joinery woodworking plans serving tray quiz is to cut grooves in the end Woodworking Plans Serving Tray Pdf pieces for the bottom. Dry-fit the sides and ends so you can transfer the location of the grooves Photo 5.

Cut these grooves straight, not angled like the ones in the sides, but use the same multiple-pass technique to make them wide enough. Lay one of the ends flat on your bench and insert the bottom into the groove. All of the curved shapes are template-routed, using two shop-made sleds, for safety Figs.

B and C, below. Each sled consists of a template, a fence and two stops. Toggle clamps hold the blanks securely and push blocks give you excellent control of the sled see Sources, below. Use a photo copier to enlarge the patterns 1 and 2, below for the templates by percent. Install each blank in the sled and mark the curves and cutouts.

Then simply saw out the middle. You have to Selling Woodworking Plans Online Quizlet rout into the grain on the front side of each arch, so make light passes and go slowly to avoid tear-out. The routing sled is a big help, because it gives you such great control of the workpiece. Sawing the narrow, rounded handles free from the blank is easy and safe when you use a simple plywood sled Photo 7. Sawing a bit wider makes them a lot longer; sawing a bit thinner makes them a lot shorter.

When you set the fence, remember that the handles are offcuts—you have to compensate for the saw kerf. Mark centerlines on the handles. Apply a thin bead of glue and rub the handle back and forth against the end. Routing the arches is similar to routing the handles.

Be careful on the front side of the arch and take advantage of the control the sled gives you Photo 9. To rout the handle hole, move counterclockwise around the inside edge Photo Dry-fit the tray, including the bottom.

The sides will be slightly taller than the woodworking plans serving tray quiz Fig. A, Detail 2, below. Plane or sand them flush. Finish-sand all of the parts prior to gluing and clamping.

This requires careful clamping, so use glue that sets up slowly. Gluing the bottom in addition to the corner joints makes the tray very rigid. Just coat the mortises in the ends and run a bead in all the grooves for the bottom. MDFfive in. Our angled clamping blocks were offcuts.

Aerosol-spray polyurethane is a perfect finish for this project. Set the tray upside-down and spray the bottom and outer sides first.

After the poly is dry, turn the tray over and spray the inside and the top edges. Spray three coats on each side, sanding between each coat. Note: Product woodworking plans serving tray quiz and costs are subject to change since original publication date. Seven Corners Hardware7corners. Shape the templates, using Patterns 1 and 2 below. Fasten the woodworking plans serving tray quiz at the bottom of the templates, exactly parallel. Then fasten the stops so they cradle the blanks dead-center on the template.

This story originally appeared in American Woodworker Octoberissue Octoberissue Purchase this back issue. Cut dadoes in the mitered ends, using a dado set. A jig made from extra mitered pieces makes dadoing safe, precise and repeatable. Cut beveled edges on the sides and angled grooves to house the plywood bottom.

Use a regular blade to cut the groove, making two or three passes, so the plywood fits snugly. Cut half-lap tenons on the sides, using the miter gauge, a sacrificial woodworking plans serving tray quiz and your dado set.

Transfer the location of the groove from the side to the end, after assembling the corner woodworking plans serving tray quiz. This method is more accurate than using a ruler. Rout both handles from one piece of wood, using a flush-trim pattern bit and a shop-made template-routing sled Fig.

B, below. Saw the handles from the blank, using a sacrificial sled—nothing more than a scrap of plywood. Fasten the blank to the sled with double-faced tape, so the small handles stay attached and stable after the cut.

Glue the handles on the roughly-shaped ends. Use centerlines and a spacer to hold the handle level and at the right height. Waxed paper keeps the spacer from accidentally getting glued on.

Rout the arched end and the handle at the same time, using a sled and a pattern bit Fig. C, below. Be especially careful not to blow out the protruding front end of the handle. Rout the handle hole. With the power off, center the bit in the hole. Push the sled forward into the bit 1 and advance the cut counterclockwise around the inside of the hole 2. Make very woodworking plans serving tray quiz passes and go slowly.

Angled blocks and a flat surface put clamp pressure on the joints. First clamp the ends to a piece of MDF 1. Then clamp the sides to the ends, using angled blocks 2. Finally, clamp the ends to the sides 3.

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness woodworking plans serving tray quiz quality. By American Woodworker Editors. Serving Tray Make one or many: simple shop-made jigs guarantee success. Miter the ends first Cut the blanks for the sides, ends and handles Fig.

Fit the corner joints Woodworking plans serving tray quiz up the saw to woodworking plans serving tray quiz the half-lap tenons on the sides. Fit the plywood bottom The last joinery step is to cut grooves in the end pieces for the bottom.

Posted on July 31, July 17, Author Gina Categories Trays - All Types Tags diy, free tray plans, pallet wood, rustic serving trays, scrap wood, serving trays Wine Caddy This beauty of a wine cadd y is perfect for transporting wine to the living room or dining room to serve guests. All dimensions of the two trays are identical except length and width. 21 in. ⁄4 in. 8 in. 18 in. side VieW end VieW 7⁄16 in. 1 ⁄8 in. 3⁄8 in. 5⁄8 in. 3⁄8 in. Side Bottom 1⁄8 in. 3⁄8 in. ⁄4 in. Breadboard end Groove, 1⁄8 in. wide by 3⁄8 in. deep, stopped 1⁄4 in. from end sMaLL traY Large traY 3⁄8 in. 3⁄8 in. Notch, 5⁄16 in. deep by 41⁄4 in. long. Feb 10,  · Vacuum the tray, wipe it with a tack cloth and it’s ready for finishing. Aerosol-spray polyurethane is a perfect finish for this project. Set the tray upside-down and spray the bottom and outer sides first. After the poly is dry, turn the tray over and spray the inside and the top edges. Spray three coats on each side, sanding between each www.- : American Woodworker Editors.

Wood Door Plans Pdf Questions Diy Shaker Kitchen Cabinet Doors Yang Under Tray Drawer Ebay Coupon Neodymium Magnets Woodworking