%!$ Easy Diy Woodworking Bench Plans For You #!@

wen-belt-and-disc-sander-parts-zone WEN MANUAL Pdf Download | ManualsLib

When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service.

Have product questions? Need technical support? READ and become familiar with this entire instruction manual. Do not use power tools in wet or damp areas or expose them to rain. Keep work areas well lit. DO NOT use power tools in the presence of flammable liquids or gases.

DO NOT work on floor wen belt and disc sander parts zone that are slippery with sawdust or wax. NEVER allow children or pets near the tool.

Do bekt wear loose clothing, gloves, neckties, or jewelry rings, watches, etc. Inappropriate clothing and items can get caught in moving parts and draw you in. Always operate the tool in a well-ventilated area and provide for proper dust removal.

Use dust collection systems whenever possible. ALWAYS remove the power cord plug from the electrical outlet when making adjustments, changing parts, cleaning, or working on the tool. Make sure the power switch is sandet the OFF position before plugging in the power cord. Always make sure all adjustment tools are removed from the saw before turning it on. Turn the power switch to OFF. Do wen belt and disc sander parts zone leave the tool until it has come to a complete stop.

Serious injury could wen belt and disc sander parts zone if the tool tips or is accidentally hit. DO NOT store anything above or near the tool. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris. Follow wen belt and disc sander parts zone for lubricating and changing accessories.

Any part that is damaged should be properly repaired or replaced before use. DO NOT operate the tool if you are under the influence of drugs, alcohol, or medication that may affect your ability to properly use the wen belt and disc sander parts zone. Normal safety glasses only have impact resistant lenses and are not designed for safety. Wear a face or dust mask when working in a dusty environment.

Use ear protection such as plugs or muffs during extended periods of operation. This sander is designed to sand wood or wood-like products only. Sanding or grinding other materials could result in fire, injury, or damage to the workpiece. Use the sander on horizontal surfaces only.

Operating the sander when mounted on non-horizontal surfaces may result in motor damage or injury. Fasten the sander securely to a bench top or supporting surface in order to stop it from tipping over or moving when in use. Make sure the sanding belt is installed in the correct direction.

See directional arrow on back of belt. Always have the tracking adjusted properly so the belt does not run sqnder the pulleys. Do not use sanding belts or discs that are damaged, torn, or loose. Use only correct size sanding belt and disc. Always hold the workpiece firmly when sanding. Keep hands paets from sanding belt or disc.

Sand only one workpiece at a time. Always hold the workpiece firmly on the table when using the disc sander and padts using the belt sander. Always sand on the downward side of the sanding disc when using the disc sander. Sanding on the upward side of the disc can cause the workpiece to fly out of position, resulting in injury. Do not sand pieces of material that are too small to be safely supported. When sanding a large workpiece, provide additional table height support.

Do not sand with the workpiece unsupported. Sandre the workpiece with the backstop or table. The only exception is curved work performed on the outer sanding drum. Always remove scrap pieces and other objects from the table, backstop, or belt before turning the sander ON. Never perform layout, assembly or set-up work on the wen belt and disc sander parts zone while the sander is operating.

Never use solvents to clean plastic parts. Solvents could dissolve or otherwise damage the material. Use only a soft damp cloth to clean plastic parts. Replace the missing, damaged, or failed parts before resuming operation. Never pull the power cord out gelt the receptacle. Keep cords away from heat, oil, and sharp edges.

Have an electrician replace or repair damaged or worn cords immediately. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. If it will not fit the outlet, have the proper outlet installed by a licensed electrician.

The conductor with the green insulation with or without yellow stripes is the qnd grounding conductor. If repair or bflt of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a live terminal.

Repair or replace a damaged or worn cord immediately. If you are not sure, have a licensed electrician check the outlet. Do not expose to rain or use in damp locations. Guidelines for wen belt and disc sander parts zone extension cords Make sure your extension cord is wen belt and disc sander parts zone good condition.

When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

The table below shows the correct size to be used according to cord length and nameplate ampere rating. When wen belt and disc sander parts zone doubt, use a heavier cord. The smaller parhs gauge number, the heavier the cord. Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Use a separate electrical circuit for your tools.

This circuit must not be less than a 12 wire and should be protected with a 15 A time-delayed fuse. Before connecting the motor to the power line, make sure the switch is in the Sanrer position and the electric current is rated the same as the current stamped on the motor nameplate.

Running at a lower voltage will damage the motor. Socket Head Screws 2 2. Miter Gauge 1 3. Washers 2 4. Work Support 1 5. Worktable 1 7. Peel backing away from sanding disc. Align perimeter of disc with plate, and press disc firmly into position on plate, leaving no loose edges. And use a screwdriver to fasten the provided screws and washers securely.

With the table in a horizontal position, line up and insert the pivot wen belt and disc sander parts zone pin with the paarts hole on the frame. Hold in place. Insert the handle into the threaded hole and tighten.

Holding the table in this position, tighten the three bolts on the top of the table. Align the Work Support with the hole. Insert the Hex Screw into the Work Support hole. Adjust the Work Support height to avoid contact with the sanding belt. Mark the workbench through the mounting holes located in the sander base. Drill holes in the workbench at the marks. Using long bolts, washers, locking washers and nuts as shown not suppliedsecure the sander to the workbench.

Page 9: Know Your Belt & Disc Sander TOOL PURPOSE Sand, smooth, and remove jagged edges with your WEN Belt and Disc Sander. Refer to the following diagrams to become familiarized with all the parts and controls of your belt and disc sander. The components will be referred to later in the manual for assembly and operation instructions. WEN 4 x Inch Belt Disc Sander Remember when you needed a versatile and reliable sander? The WEN Belt Disc Sander easily sands, smooths and removes all of the jagged edges and splinters on your wood and lumber. With a amp 1/2 HP motor, users should anticipate enough power to prevent this machine from bogging down under a large load/5(K).

Diy Mini Cnc Machine 980 Woodwork Drawing Software Google Woodworking Plans For Castle Quantum