%!$ Easy Diy Woodworking Bench Plans For You #!@

waterlox-original-sealer-and-finish-out Waterlox Original Sealer/Finish - Waterlox Original Finish sold at Highland Woodworking - authorized Waterlox Dealer.  Waterlox Original Sealer/Finish. Waterlox has served generations of floor installers, turners, carvers, and furniture makers as a reliable, easily applied tung-oil-based varnish. Polymerized tung oil, ester gum, polymerized linseed oil, and a high ratio of phenolic resin allow it to build a tough surface film which resists scuffs and staining admirably. Apply by wiping, brushing, rolling, spaying or (on flooring) with lambswool pad; thin and clean up with mineral spirits or turpentine.  Repair is easy: sand out the damage and recoat! Coverage is around square feet per gallon per coat; soft woods require more coats than very hard woods. Waterlox Original Sealer/Finish. Nothing better in my opinion for black walnut table tops. Soaks deeply into wood, not affected by condensation moisture from drink glasses.  Best Answer: Waterlox, stands for "locks out water.” Therefore, Waterlox Original Tung oil finishes are the perfect solution for any and all wood finishing project(s). When you add to that your plans to finish a floor or a known water-related area like a bathroom, kitchen, counter top or table top, we think Waterlox should be the only finishing choice since no other clear finishes, surface finishes or raw oils. available on the market today have superior protection and water resistance properties. Apply Waterlox ORIGINAL Sealer/Finish liberally with the grain using a lamb’s wool applicator (floors) or a quality natural bristle brush or paint pad. Allow to dry for 24 hours. Repeat steps for a second (for soft wood species, a third) coat. Sanding between coats of Waterlox ORIGINAL Sealer/Finish is not necessary for adhesion but can be done for aesthetic reasons.  Pour out the Waterlox ORIGINAL Sealer/Finish product into a paint tray. Dip the applicator fully into the paint tray to saturate it. Following the grain, pull the applicator (spread the finish) toward the opposite wall evenly. Hold the applicator with light pressure and at a slight angle to maintain a wet edge. To avoid lap marks, maintain a wet edge by overlapping sections previously finished by several inches. Need Application Instructions? FIRST AID: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. Find the appropriate application guide based on the products and surface size you are using. Lead is toxic. I waterlox original sealer and finish out daterlox that streaking occurred also.

Step 2 After sanding it is very important to remove every speck of dust on the woods surface. First use a vacuum to pick up all the dust and then use a lint free cloth with a little mineral spirits on it to remove any remaining dust particles. Allow the mineral spirits to evaporate off the wood completely. Next wash your hands to free them of any oils then wipe the surface of the wood off with your bare hands to remove any remaining dust or lint particles.

Step 1 Pour some Waterlox into a clean glass container. Run the tip of the foam brush over the edge of the glass container to remove a small amount of Waterlox to prevent drips. Step2 Brush the Waterlox onto the wood surface following the grain of the wood. You will notice that the wood almost soaks up all the Waterlox in a short period of time.

Allow this coat to dry under perfect conditions for twelve hours. There is no need to worry if you see small bubbles in the finish. Cross ventilation will significantly speed up the drying process. Step 3 After you have allowed the Waterlox to thoroughly dry apply another coat of Waterlox Original in the same manner you did in step 2. Allow to dry thoroughly for at least 12 hours or more if needed.

Step 4 Lightly sand the wood surface that you applied the Waterlox on with grit sandpaper. Two or three firm passes will do.

You will notice white dust appear as you sand. Wipe away any dust in perpetration for the next coat of Waterlox. Step 5 Apply another coat of Waterlox and allow it to thoroughly dry as you did in step 2. This will be the 3rd coat. Step 6 After the 3rd coat has dried you will want to sand lightly with grit sandpaper and then grit sandpaper. Clean all dust from the surface. Step 7 This will be the final coat. If you want or feel that you want another coat before the final coat then repeat step six.

For the final coat you will want to apply a liberal coat of the Waterlox Original. Apply a liberal coat along the wood grain in one long, smooth stroke.

Cross ventilation will help significantly speed up the drying and cure time. After coating the entire surface allow the Waterlox to rest for about 20 minutes. Using a new dry 4 inch foam brush go over the Waterlox in one long smooth stroke. Allow the Waterlox to rest again for 10 to 15 minutes. You will want to continue dry brushing your Waterlox with the 4 inch foam brush every 5 or 10 minutes.

You can not over dry brush the Waterlox. You will find that you end up with a very beautiful and defect free wood finish that will last a lifetime as you can see in the pictures below. Waterlox Problems: How to use waterlox finish without problems I have been using Waterlox Original for several years now and am very satisfied with the results I have achieved with it. Some typical problems I was having at first with Waterlox Original were: Micro Bubbles in the Waterlox finish Rough finish Streaking After encountering these problems I turned to the internet for help and found most articles stated that it was the easiest finish in the world to Waterlox Original Sealer And Finish 800 apply and was fool proof.

A few myths I have read online about Waterlox Original are: You must stir and not shake Waterlox or you will have bubbles. Properly dispose of rags, applicators and waste. Rags, steel wool or waste soaked with Waterlox may spontaneously catch fire if improperly discarded.

Immediately Waterlox Original Sealer And Finish 65 after use, place rags, steel wool or waste in a sealed water-filled metal container. Read carefully other cautions on the product label. Visit the cleaning and care guide for more information. Visit the re-coat and maintenance guide for more Waterlox Original Sealer And Finish 85 information. This guide is intended to be a standard application procedure. NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage.

Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Keep away from heat and flame. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying.

Close container after each use. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling. FIRST AID: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water.

If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. If swallowed, do not induce vomiting.

Do It Yourself Home Garden Journal Best Woodworking Belt Sander Vessel Diy Wood Panelling Ideas Pdf Flush Trimming Zero