%!$ Easy Diy Woodworking Bench Plans For You #!@

vise-grip-clamps-woodworking-valve Vise-Grip Clamps | McMaster-Carr

We may receive a commission when you use our affiliate links. However, this does not impact our recommendations. As a professional woodworker, leaving the comfort of my shop to work on a jobsite clam;s part of the routine. I had a portable bench, but without vises, it was only marginally useful.

Vise grip clamps woodworking valve all the classic woodworking vises on a jobsite would be really sweet; and expensive. What I needed were simple, durable vises that I could build on a budget. I came up with three classic woodworking vises that can be adapted woodworiing any existing bench, using any pipe clamps. The face vise is the workhorse of any bench.

Typically, it holds boards so their edges can be worked. This is vise grip clamps woodworking valve simplest and most-used vise of the three. Two pieces woofworking hardwood, such as oak, make for a stiff, rugged jaw. Use a drill press to drill the holes for the pipe and guide rod C through both the jaw and the mounting vse Fig.

The guide rod prevents the jaw from spinning. Next, separate the mounting block and jaw, and drill the lag screw holes in the mounting block. Reinstall the sliding head, and then tighten the clamp on the two parts, with the stationary head positioned vertically, and the sliding head positioned horizontally. Fasten the heads to the jaw and mounting block using screws, and secure the guide rod with a cotter pin.

To adjust the vise, reach to the back of the mounting block to squeeze the clutch plates. The tail vise, typically used in conjunction with bench dogs, is used for holding parts flat for face work.

Mine has an adjustable guide board, similar to a leg vise. The guide board keeps the jaw from spinning and vise grip clamps woodworking valve the vise to hold large workpieces.

Like the face woodworrking, first glue-up the jaw A and faceplate B assembly. You could probably get by without the faceplate, but a stout wood like oak stands up to hard use much better than pine.

Square up the assembly using vise grip clamps woodworking valve jointer and planer, if available. If not, a tablesaw or circular saw will do. Also, drill out the mortise for the pin board Fise. A Forstner bit works best for this, because it lets you overlap fise holes. As before, clean woldworking the mortise using a chisel.

Drill the adjustment holes in the pin board Fig. Assemble the two parts. The knockdown pin makes full disassembly easy for transport. I added a wooden knob to my pin to make it visw to remove. Drill screw holes in the clamp heads. Insert the pipe into the jaw and slide the assembly into position on the bench. Reinstall the sliding head, tighten the woodwor,ing and install the clamp head mounting screws.

Like the face vise, reach under the bench and squeeze the clutch plates to adjust the clamp. Insert the adjustment pin in the hole that gives you the vise grip clamps woodworking valve opening best suited to your workpiece. Adjust the pipe clamp by squeezing the clutch plates to release their grip. The Moxon vise is essentially a face vise with two screws.

My design also features a quick-release handle. Named after its inventor, 17th century woodworker and author Joseph Vise grip clamps woodworking valve, this vise specializes in securely holding wide boards.

Two woodeorking provide even pressure across the whole board without any racking. Another benefit of the Moxon vise is its height. When you need to be close to your work, vise grip clamps woodworking valve as when cutting valvee, this is the vise to use.

A good vise must be extremely stable. To build the vise, glue up the front jaw pieces A and set the assembly valv. Meanwhile, assemble the top and bottom Bincluding the buildup C and filler D pieces. Use a plywood offcut as a spacer to create the dadoes.

Trim the front jaw to final dimension, and round over vize outer edges if you woodworjing. Turn the assembly upside down and position the front jaw, rear jaw Grear jaw buildup Hand clampa blocks J. Mark and drill woodqorking front jaw holes using a drill press and then reposition the front jaw on the assembly. Finally, drill the holes in the ends of the guide blocks Fig. Next, cut out the levers K, Fig.

Drill the holes in the levers, cut the bridle joints, chamfer the handle, and glue the dowels M in the levers. After the glue dries, slide the guide blocks onto the dowels do not glue and screw the whole assembly in place.

Before attaching the bottom, assemble the vise like you did the other two vises; by removing the sliding heads and inserting the pipes through the jaw assembly. Set the push bar N, Fig. Lastly, attach the bottom using glue and vise grip clamps woodworking valve. Pull the handle towards you to release the clutch plates for quick adjustment of the front jaw.

Here are some supplies vise grip clamps woodworking valve tools we find essential in our everyday work around the shop.

We may woodwlrking a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality. Thanks for this great idea. Thanks, Chad. Detailed, simple-to-build-and-afford projects like these reiterate vose makes you such a valuable resource in the woodworking community. Chad, you nailed this! Workbench vises are way out of my hobbie price range, but here is a very affordable option.

The detail included in your article is excellent. I plan to make three with my son, son in law, and of coarse, one for me. By Chad Frip. In Feature Articles. The Face Vise Vise Grip Clamps Woodworking 100 The face vise is the workhorse of any bench. Face Vise. Pipe and Guide Rod Locations. Tail Vise. Guide Board Hole Pattern.

Moxon Vise. Guide Block End Hole. Push Bar End Taper. JMarshall64 January 31, All rights reserved Privacy Policy Terms of Use. Start typing and press Enter to search. My Therapeutic Shop Interviews.

IRWIN VISE-GRIP Original locking tools, with a classic trigger release, are designed to provide maximum locking force. IRWIN VISE-GRIP has been the go-to tool of professionals since Shop from locking pliers to wrenches, crimpers, cutters and more.

Sign Router Jig Yield Wood Shop Counter Quality