%!$ Easy Diy Woodworking Bench Plans For You #!@

used-craftsman-radial-arm-saw-ic radial arm saw craftsman for sale | eBay

Table of Craftsmann Section Title Repair Parts If within one year from the usef of purchase, this Craftsman Radial Saw Guard Kit fails due to a defect in material or workmanship, Sears will repair it, free cratsman charge. Severe cuts, and loss of fingers or other body parts due to contact with the blade. Eye impact injuries, and blindness, from being hit by a thrown workpiece, workpiece chips or pieces of blade, 3.

Bodily impact injuries, broken bones, and internal organ damage from being hit Used Craftsman Radial Arm Saw For Sale Video by a thrown workpiece 4. Shock or electrocution 5. Major Hazards Three major hazards are associated with using the radial arm saw for ripping, They are ouffeed zone hazard, kickback, and wrong way feed. This section used craftsman radial arm saw ic briefly explains these hazards. Read the ripping and crosscutting safety sections of your saw manual for more detailed explanations of these and other hazards.

Safety Symbol and Signal Words An exclamation mark inside a triangle is the safety alert symbol. If you reach around the blade to the outfeed side when ripping, and try to hold down or pull used craftsman radial arm saw ic workpiece through to complete a cut, the used craftsman radial arm saw ic force of the blade will pull your hand back radoal the blade. Fingers will be cut off.

Read and follow all safety information and instructions. When a workpiece kicks amr, it could hit hard enough to cause internal organ injury, broken bones, or death. Wrong Way Feed Hazard Wrong way feed is ripping by feeding the workpiece into the outfeed side of the blade.

The rotational force of the Used Craftsman Radial Arm Saw For Sale Australia blade can grab and pull the workpiece. Before you can let go used craftsman radial arm saw ic pull back, the force could pull your hand along with the workpiece into the blade. Fingers or hand could be cut off. Wrong Way Feed. Regular eyeglasses are not safety goggles. Wear close fitting clothes, short sleeved shirts, and non-slip shoes.

Tie up long hair. Used craftsman radial arm saw ic not wear gloves, ties. These can get caught in the spinning blade and pull body parts into dae blade. Wear dust mask to keep from inhaling fine particles. Wear ear protectors, use saw daily. Keep children, pets, and visitors out of work area; they could be tilt by a thrown workpiece, workpiece chips or pieces of blade. Turn saw off, remove yellow key, and unplug before leaving work area.

Do not leave until blade has stopped spinning. Make work area child-proof: remove yellow key to prevent accidental start-up; store key out of sight and reach; lock work area.

Keep floors clean and flee of sawdust, wax and other slippery materials. Keep rasial area well radiwl and uncluttered, 6. Use saw only in dry area. Do not use in wet or damp areas. Keep them in working used craftsman radial arm saw ic. Repair or replace damaged parts before using saw. Unplug saw before doing maintenance, making adjustments, correcting alignment, or changing blades.

Do not used craftsman radial arm saw ic saw. Use saw, blades and accessories only as intended. Before turning on saw, clear table of all objects except workpiece to be cut and necessary fixtures, clamps, or feather-boardso.

If blade jams, turn saw off immediately, remove yellow key, the free blade. Do not try to free blade with saw on. Do not layout, assemble, or setup work with saw on, or while blade is spinning. Keep saw table clean. Store items away from saw. Do not climb on saw or stand on saw table to reach items because saw can tip over. Cut only one workpiece at a time. Stacking or placing workpieces edge to edge can cause user to lose control of workpieceo.

Safety 3. Rip only workpieces longer than the diameter of the blade. Do not rip workpieces that are shorter than the diameter of the blade being used. Used craftsman radial arm saw ic that extend beyond the saw table can shift, twist, rise up from the table, or fall as they ar'e cut or afterwards.

Support workpiece with table extensions the same height as the saw table. To prevent tipping, support outer ends of extensions with sturdy legs or an outrigger.

Do not use another person to help support workpieces or to aid by pushing or pulling on workpieces, because these cravtsman can cause sxw. Use table extensions. Use clamps used craftsman radial arm saw ic vice to hold workpiece. Do not overtighten blade nut because blade collar could warp 6o Do not turn saw on and off in rapid sequence craftzman blade can loosen.

Blade should stop within 15 seconds after saw is switched off. If blade takes longer, the saw needs repair. Contact Sears Service Center. Use only 10" or smaller diameter blades. Use blades for their recommended procedures. Keep blade sharp and clean. I B Rear Table 40" Izront Fable 40" I E Tahte Supporl Handle Assembly Bag Ol Loose Parts I Conlaining: I I.

Adapter Motor Key Bag Ol Loose Paris Assembly Guard screws, Installation existing Steps table boards. Keep all including the lev1. Remove Note: boards This retro fit guard behhM are being supplied kit requires fence, additional clearance New table.

Discard the old table boards but keep the fence. Install used craftsman radial arm saw ic. Refering to your saw owners manua! Remove the front table. The U-Clips that were used as nuts for the rear screws must be moved to the new screw location Remove them from the saw and reinstall them on the table.

Referring to your saw owners manual, install and level the table boards. Remove crosscut travel may no Ionger to your saw owners tlavel. Rotate the saw to the outrip position. Remove and discmd ttle oflmr lmndle retaining screw, Discard tile crattsman handle, 8. This locks tile adapter in place. Lock motor at 0 bevel blade vertical. Position guard so riving knife fuces front of saw. Blade pinching is a cause of kickback, 1.

Lock yoke in in-rip position blade towards column, motor towards front of arm. Lower arm until blade just clears table, 3. Unlock rip lock while holding up lower plastic guard, move yoke back until blade touches fence.

Lock rip lock. Lower riving knife to the table and tighten knob. The riving "knife should rest fiat against fence, 5. If adjustment is needed: 1o loosen riving knife bracket screw. Z slide riving knife so it rests against fence.

Frees radial arm to move; locks in any desired position; pro-set indexed positions at 045L, 45R Turns motor on! Insert into on-off switch Remove after turning saw off Move towards right to unlock, towards left to lock Support motor before unlocking because it can swing down quickly.

3-Phase Radial Arm Saw. 3- Phase Radial Arm Saw. Volt. 3 hp motor 14" blade. Runs good and is in good condition. Bidders are Strongly Encouraged to verify the condition of items listed in this auction. Items Sold "As-Is" The B.

Diy 4 Rail Wood Fence 72 Jig System For Handles Knobs And Case Volume Best Flush Trim Router Bit Question Woodworking Sanders Safety Shoes