%!$ Easy Diy Woodworking Bench Plans For You #!@

lathe-tool-post-t-nut Токарный станок по металлу Craftsman & Lathe tool post t-nut,Tapped for 14xmm thread. Токарные станки по металлу. 17,00$. Цена. 17,00$ USD. USD. Токарный станок по металлу Atlas circa,Atlas 10" & 12" Lathe's,tool post t-nut,Tapped for 3/ thread. 6" Atlas & Lathe tool post t-nut,Tapped for 3/ thread. Войти в систему для оформления покупки. Оформить покупку без регистрации. Добавить в корзину. Добавить в список отслеживания Удалить из списка отслеживания. Список отслеживания заполнен. 7 отслеживающих. Home-Made Tool Posts. T-Nut for Tool Post. Home-Made Tooling. Tweco Adapter for Clarke MIG. Wire Rollers For MIG Feeders.  Note: you don't want any radius in the corner. That will cause the nut to try an pry the T-slot apart and possibly crack it. Easisest is to move the bit farther into the corner. In this case it was ground off later and was a pain to do.

Forum Rules. This website or its third-party tools process personal data e. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by lathe tool post t nut or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise.

Login to Your Account. Remember Me? Register Forgot password? What's New? Likes: lathe tool post t nut. Results 1 to 12 of Thread: Lathe tool post T nut question? Thread Tools Show Lathe tool post t nut Version. When making the lathe tool post t nut plate for a tool post is it necessary to make a full T nut or is just a flat plate fitting the botom of the compound sufficient?

A complete T would give you more threads for the mounting stud but is there any other reason for doing it? Thanks in advance lathe tool post t nut any comments. Join Date Mar Location W. Mike, its 'your call' Do you need the greater length of thread for strength in the application? As a generality, one diameter is considered a practical minimum thread length, i.

Carla, it is for a 12" Clausing Mike, With just a flat plate you are, as Carla stated, shorting yourself a few threads for strength. But, additionally, you are providing a lot of "air space" above the plate and the top of the top slide.

If you go this route, machine yourself a thick slug fat washer that spans the width of your compounds upper t-slot and fits snugly around the tool post lathe tool post t nut. Leave it a few thou shy of the exact top because when you tighten the bolt down with only a lathe tool post t nut plate underneath there will be more upward flex than normal and you want your toolpost to be secure without bottoming on the slug.

Also, drill and tap the plate for a couple of set screws and snug it down to the compound slot to keep it from slipping out each time you loosen to make a toolpost adjustment. What I am thinking of doing is to weld a piece of flat stock to the bottom plate to have more thread engagement. To mount a quick change on my SB9 I used a flat plate with a bolt welded to it. The nut goes on top. Mike, That will work, but you have a lathe. Select a plate thicker than you need.

Chuck it up in the 4-jaw and turn the face down so the chucked up piece will fit the lower T-slot and the diameter you just turned will fit the top slot of your T-slot. You know. You end up with the flat plate with a donut on top.

Drill it and tap it, and countersink from the back side. Turn a bit of length off the capscrew head; thread it in from the back side and loctite it in place. Slide this all in the T-slot, drop your toolpost over the new stud, and tighten a nut on top.

Welding is faster. If you use a plate, even with spacer nuts, etc. Slippage back might be an issue if you try to push the bit in too much. Tee nuts are rigid and hae a lot of contact. BUT, if THINK you will ever need to take big bites or be machining hard materials that will want to lathe tool post t nut your tool back, make as big as a tee nut that will fit the compound for the most rigidity.

I just mounted an AXA to my Rockwell 11" compound. It came with a "nut" more of a threaded plate really to fit the t-slot. But it was a bit wide and tall for my compound slot. So I put a few layout lines on it to remove equal amounts from both sides and then a t-nut like notch in the top side. This fits my slot well but plenty of room to move easily without any chance of cocking and binding. Basically this forms lathe tool post t nut rather large t-nut lathe tool post t nut fully fills the lower width and about half the narrow slot.

That left the original stud bit too tall needed 2 washers to tighten AND the tool post could hit the compound in some rotations. Looks like a big washer, 2. That left about 0. I expect I will do a bit more after I see how it works. The tool post is one of the focal points of your machine. Do a nice job so as to have something pleasant to look at that satisfies you unless you are in a hurry and just can not stand the production lost.

Bookmarks Bookmarks Digg del.

Tool posts with blank T-nut come with a T-nut that must be machined to fit your lathe’s T- slot. Tool posts with custom T-nut come with a T-nut that has been machined to fit your lathe’s T- slot. To order: Provide the base width, base height, slot width, and overall height of your lathe’s T- slot. Mar 13,  · Find many great new & used options and get the best deals for Atlas circa,Atlas10" & 12" Lathe's,tool post t-nut,Tapped for 14x thread at the best online prices at eBay! Free shipping for many products!Seller Rating: % positive. Aug 12,  · Quick Change Tool Post T-Nut For The South Bend Lathe August 12, / 4 Comments / in Bridgeport, Southbend / by mick I finally got sick and tired enough of the sloppy feel of the T-nut on my Aloris tool post and decided to make a “corrective” base to bridge the wallowed out compound on my South Bend Lathe.

How Do Jet Planes Generate Electricity Numbers Bowl Turning Chisels 80