%!$ Easy Diy Woodworking Bench Plans For You #!@

jet-jml-1014-mini-wood-lathe-manual-check Safety Goggles Restore password. Reitstockbohrung Die bauliche Absicherung muss dabei Pinolenhub 50mm 10A betragen. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions mnii may affect its operation. Keep proper footing and balance at all times. Please have the following information ready: 1.

Serious injury could occur if the tool is tipped or if the cutting tool is. Before further use of the tool , a guard or other part that is damaged. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any. A guard or other part that is damaged should be properly. Feed work into a blade or cutter against the direction of rotation of the blade or.

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric. Th is tool is equipped with an electric cord having an. The plug must be plugged into a matching outlet. Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified.

Improper connection of the equipment-grounding conductor c an result in a risk of electric shock. If repair or replacement of the electric cord or plug is necessary, do not.

Check with a qualified electrician or service personnel if the grounding instructions are not completely. Use only three wire extension cords that have three-prong grounding plugs and three-pole receptacles. Repair or replace a damaged or worn cord immediately. This tool is intended for use on a circuit that has an outlet that looks the one illustrated in Figure A below. The tool has a grounding plug that looks like the grounding plug as illustrated in Figure A below. The green colored rigi d ear or tab, extending from the adapter, must be.

Specifications: JML Stock Nu mber Swing Over Bed In. Working Distance Betw een Centers In. Number of Speeds Range of Speeds R PM Headstock Spindle Th reads T. Headstock Spi ndle T aper Tailstock Spi ndle T aper Hole Through Ta ilstock I n.

Tailstock Ram Tr avel In. Toolrest Lengt h In. Overall Dimensions In. Net Weight l bs. Shipping Weight lbs. Twist Pen Kit Plunger Type Penc il Kit Mont Blanc Style Pen Kit Mont Blanc Style Letter Opener Wood Blanks Exotic Hardwoods 5 piece Drill Bit 7mm Wax Pen Fini shing Kit Insta-Cure Glue Pens from the Woodlathe Book The specifications in this manual are given as gener al information and Jet Jml 1014 Mini Wood Lathe Manual Rating are not binding.

JET Equipment. Remove contents from the shipping box. Inspect contents for shipping damage and. Be sure to keep the box and packing. Do not clean the lathe with anything other.

However, it is. Tailstock Handw heel A, Fig. Tailstock Spindle Lock B, Fig. Tailstock Lock C, Fig. Spur Center A, Fig. Face Plate A, Fig.

Drift Rod Jet Jml 1014 Mini Wood Lathe Manual Facebook A, Fig. Stored in the hole in. Tool Rest Fig. Position the tool rest as close to the work piece. Adjust the height of the tool rest. Disconnect the machine from the power. Open the access doors at the left side of the. Loosen the motor plate lock handle A, Fig. Lift up on the motor plate handle B, Fig. Move the belt B, Fig.

Tension the belt by pushing down on the. Loosen the set screw B, Fig. Loosen two set screws in handwheel C,. Remove handwheel and pull the spindle out. Place the new belt on the spindle pulley. Insert the spindle into the spindle pulley. Thread the handwheel onto the spindle. Center the spindle pulley and tighten set. Wrap the belt around the motor pulley. Tension the belt and tighten the motor plate.

Loosen tailstock lock handle B, Fig. Turn the tailstock handwheel A, Fig. Before installing the live center into the. Index Part. Description Size Qty. Headsto ck Whit e Headsto ck Spur Center Center Po int for Spur Center not shown Ball Bearing Wave Washer Set Screw J ML Drift Rod Spindle Pulle y Door White Spi ndle Pulley Door Previous Page.

Next Page. Jet tools wood lathe operating instructions and parts manual jwlvs 32 pages. Page 4: Remaining Hazards 4. Keep the floor around the machine clean and free of scrap material, oil JMLI: Do not remove chips and workpiece and grease.

Swing over bed mm parts until the machine is at a Page 5: Noise Emission Clean all rust protected surfaces with 10 A surge-proof fuse. Only use power cords marked 7. Page 7: Maintenance And Inspection Reitstockbohrung Die bauliche Absicherung muss dabei Pinolenhub 50mm 10A betragen. Page 11 5. Setzen Sie ein geeignetes Absaug- bzw.

Filtersystem ein. Page 12 Werkstoffe. Bitte entsorgen Sie es nur an einer spezialisierten Entsorgungsstelle.

Furniture Drawer Slides 3d Belt And Disc Sander For Knife Making Line Best Entry Level Wood Router 05