%!$ Easy Diy Woodworking Bench Plans For You #!@

build-router-table-cabinet-20 Great short and to the point video — the kind I like. I'm curious, will check him out for sure. Yes No. Submit a Tip All tip submissions are carefully reviewed hable being published. There are detailed sections on Joinery for hardwood plywood and Perfect, simple drawer joinery which are very helpful.

However, this does not impact our recommendations. Since you are an affiliate, you can use this url to link people to this page and get credited for it:. Tier Standard Premium unavailable Learn more about our premium plans.

Premium Files You can download the additional shop drawings that you purchased using the link in this box. What You Get: 10 printable digital pages of step-by-step instructions Over 40 full-color photos and illustrations and exploded views Cutting diagram and materials list. Cord Grommet Shop now at Amazon. You'll find plywood cutting diagrams on my website - click here.

To assemble the drawers, I first applied some glue to the seams and used brad nails to help hold the box together while I screwed in some pocket screws. With the slides assembled, I applied glue all along the bottom and dropped in the bottom panel that I secured with brad nails. This was my first time working with drawer slides but the process is pretty simple.

Holding it firmly in place, just pull the slide out and find the screw holes to secure it to the cabinet. Next you can pull the drawer out just a bit along with the bottom spacer and attach the slides to the drawer, then work your way back to the following screws. For the upper drawer, I repeated the process using my Kreg drawer slide jig which made the job easy. To attach the drawer faces, I started with the bottom so I could use the table to line up the bottom with the cabinet.

I clamped the face to the drawer box securely, then slid out the drawer and used a countersink bit to drill some holes in from the back, then secured the face to the drawers with some screws. I repeated the same process for the upper drawer, but used washers as a spacer between both drawers. Before the cabinet gets too heavy, I decided to move it to the floor. I first however flipped it on its back and attached some 3 inch caster wheels using some lag screws.

I used some Weldbond glue to create a seal and attached it to the cabinet with some screws. For the top part of the cabinet, I wanted to add small drawers, but decided to go with simple wooden slides that I nailed into place with my brad nailer. I repeated the same pattern on a second panel, then checked to make sure my drawer bottoms Build A Compact Router Table Noise would fit before securing the panel to the cabinet with some pocket screws.

The top middle section is going to be a door so I can easily access my router from underneath if I have to. I used a hinge jig with a 35mm Forstner bit to countersink the hinges. Using washers as spacers on the bottom, I mounted the door, and made the final adjustments using the adjustment screws. Using my trusty washers to get the spacing just right, both on the bottom and on the side, I clamped on the face, drilled some countersunk holes from the back, and secured the face with some screws.

After that it was rinse and repeat for all 6 drawers. To attach the knobs, I used this Kreg drawer pull jig to help place the knobs consistently.

After lining up the top to where I wanted it, I attached it from underneath with pocket screws using the pre-drilled holes I had made. After mounting the switch to the door on the side closest to the hinge, I used a Forstner bit to Build Your Own Router Table Free Plans Up make a hole and feed the wires through. Be sure to Build Your Own Router Table Video Editing check Plans To Build Router Table Size out the video tutorial if you haven't already done so.

If you like what you see, subscribe to my YouTube channel to get notified when I post new builds. Nice router table. It looks pretty similar to The New Yankee Workshop's version. I actually made mine from Norm Abram's plans. I deviated some to fit my needs but it is close. And it looks pretty close to yours as well. It is one of the best things I've built for the shop.

I built mine from MDF and hard woods because it is very heavy and a router table need to be solid. And I also used dual locking casters so it stays put when I lock them.

Here is a picture of mine. You can see the similarity. Reply 2 years ago. Yours looks great too. I can see the similarities. I've actually added a few holes in the center compartment as well for better air flow. Yea, I got those holes for the air flow.

Makita 2301 Router Zoom Woodworking Crafts Stores Near Me 01 Saw Dust Vacuum 90