%!$ Easy Diy Woodworking Bench Plans For You #!@

woodworking-plans-jewelry-box-60 DIY Jewelry Cabinet. At least, this is the plan :. Sophie's Box. The wood in woodworking plans jewelry box 60 series of jewelry boxes is mahogany. Antique style jewelry box plan. There's a materials list, cut list, step-by-step directions, and lots of diagrams included. Secure wooddorking joints with a couple of clamps and check for square before setting the drawers aside to dry.

Comic Book Jewelry Box. Build a Wooden Box. Free Wooden Box Plans. Creating a Puzzle Box. Keepsake Box Plans. Build an awesome jewelry box. Build a few simple boxes. Make a Box Joint Box. A Bandsaw box. Jewelry Box - tutorial. Wooden lock box. Iris Box tutorial. Puzzle Box Safe Plans. How to make a simple box. Ring Box Plans. Keepsake box. Music Jewelry Box. Hidden Treasure Box. Pallet wood Jewel box. Puzzle Box plans.

Secret felted keepsake box. Nesting Trays Box plans. Trinket Box Plans. After releasing the frames from the clamps, sand the top and bottom edges of the doors to create clearance in the door openings. I used a pair of brass-plated, no-mortise hinges to mount my doors on the cabinet. To enhance the grain of the cherry parts, I applied some cherry gel stain, followed by three coats of wipe-on polyurethane.

When you apply this finish, tape off surfaces to be glued later on the backs of the front columns and the sides of the drawer boxes. Bare, unfinished wood is essential for the glue to work.

I used black aniline dye to colour some of the exposed maple surfaces of the cabinet. Start by brushing on distilled water to raise the grain.

Let the surfaces dry completely, then use grit paper to sand off the fibres that have lifted. Repeat this process a couple of times to be certain the grain will remain flat when the dye finish is brushed on. I find that a foam brush works best to apply the finish, but be sure to wear gloves to prevent a mess on your hands. Simply do your best to keep the dye off the sides of the drawer compartments because it may cause the drawer runners to swell, preventing the drawers from sliding smoothly.

After brushing on the dye, wait 24 hours before applying several coats of wipe-on polyurethane. The additional coats enhance the richness of the black finish. Next, line the drawer boxes and cabinet compartments with adhesive-backed felt. You could use powdered flocking that is dusted onto a glue-covered surface, but I find peel-and-stick felt easier and neater to apply.

After lining the side compartments, install hooks for chains and necklaces. I used a pair of brass-plated key-box hooks for my jewelry box. They are simply fastened in place with a couple of brass screws. This is also an opportune time to mount the bevelled mirror on the underside of the lid. After all the interior work is done, glue the vertical columns to the front of the cabinet and reattach the doors and lid. You will also need to drill holes to install the drawer pulls and knobs.

The knobs I chose are glued in place with epoxy. Finish up by mounting latch mechanisms to secure the doors when they are closed.

There are many options, but I settled on tiny rare-earth rod magnets recessed into the edge of the compartment frames. As a final touch, why not write a meaningful message to your loved one on the back of one of the drawer boxes to make this special gift even more memorable?

Latest Items. Tweet Pin It. Pin It. This is performed after the components are sized to the inside lid. Shooting the ends of drawer and tray components guarantees a perfect degree joint or corner for the inside lid components. The shooting board can be used to shoot either 45 or 90 degree ends of components. Perfect miters are critical as gaps in joints take away from the quality of the jewelry box. The inside of a lid with frame components and inside panel installed.

There are a few more steps to follow before application of the engraved brass plate. A carved wood mount to which the brass plate is affixed is handcrafted next. The carved wood mount is centred in the top inside panel and the brass plate in inlaid into the wood block.

A White Mountain Design brass insignia has been applied to the inner lid and all frame and panel members have been glued in. The gold-plated lock and the wood mount for the customized brass plate are next. The combination of brass maker's mark and personalized brass engraved plate add a level of craftsmanship to the product. The gold-plated lock has been installed in one of our black cherry jewelry boxes. The escutcheon is only temporarily mounted for fitting purposes.

The lock has been tested for proper operation. Extreme care is taken to fit these locks as the process cannot be reversed and any damage or errors essentially trash the jewelry box.

Two completed jewelry boxes ready for delivery. The exteriors have had finish applied and have been hand-rubbed. The interior compartments are lined with velvet and ring holder compartments installed in each of the sliding trays. Personalized brass plates and holders have been completely installed. The personalized brass plates can now be seen installed.

The completed jewelry boxes with bottom drawer open for a better idea of the size of the drawer compartments. Each jewelry box has slightly different characteristics in the graphics or grain pattern of the body and the figure of the bird's eye top. The client is essentially receiving a unique, one of a kind product even though the dimensions are standardized between jewelry boxes.

An exterior or bird's eye view of the same jewelry boxes. The contrast between the black cherry body and the light bird's eye tops can be seen here. Often, I will have a few of these jewelry boxes in different combinations of woods available so a client can select their choice from inventory.

As I like to mention to my clients, now comes the expensive part, filling the jewelry box :. Another variant of the jewelry box. This is a mahogany jewelry box with a solid raised top. Client opted not to have Maker's Mark installed. Some clients like it, others prefer that the engraved brass plate remain the focal point of the inside lid of the box.

These jewelry boxes are fairly large at 14 in. From previous research, clients prefer this size. This jewelry box has a spray lacquer finish applied to both maintain the clarity of the wood and to create a durable outside finish. Other options are a shellac-based finish and an oil-based finish. I typically apply the oil-based finish to the walnut version of the jewelry box.

Each of the drawer and trays have now been lined with padded velour. The jewelry boxes continue to be created to this day at White Mountain Design in small batches.

I create the batches a few times a year to ensure some inventory is Woodworking Plans Jewelry Box Co maintained. For woodworking plans, courses and tutorials and videos, please visit WoodSkills. But it seems that if you go through all the work of posting such detailed pictures it would be nice to give dimensions. Question 1 year ago on Step Answer 1 year ago. Drawer front is wood from the same plank with grain pattern and color that is close or matches the rest of the jewelry box exterior.

So if you look closely, there is a minor discrepancy. This is the only way I could work this out. So the drawer front is not the piece that was cut out of the box front. Thx, Norman. Do you by any chance have one in stock? Could I order one?

Thanks in advance for your reply. Reply 2 years ago. Not doing any jewelry boxes right now.. I'm documenting the build on Instagram woodskillsmag Thanks, Norman.

Free Diy Woodworking Plans 800 Ridgid 10 Inch Table Saw Accessories Carpenter Wood Design Job Woodworking Miter Saw Review Guideline