%!$ Easy Diy Woodworking Bench Plans For You #!@

Bathroom medicine cabinets made almost entirely from reclaimed materials. The H shaped pattern in the door run perpendicular to the shelves inside the cabinet. The main frame is made from salvaged pine which used to live as wall paneling in a church on Cape Cod. The weaved panels are created from PVC sheet packing material and formed to the weaved pattern.

I start by grabbing a bunch of boards of my reclaimed pine paneling. All the pieces are cut down to rough length on the miter saw and then these pieces are all cut to final width on the table saw. I then use the miter gauge on the table saw to cut all the pieces to final length.

The main pieces around the perimeter of the cabinet are cut at 45 degree miters. I use my setup blocks to set the height of the blade and also set up the fence to cut the tongues in the end of the pieces for the door panels.

These are cut little by little, nibbling away to form the tongue. Then the grooves prokects cut in all the door pieces mrdicine will fit the panels and also fit the tongues from the perpendicular pieces.

The finger board wood projects medicine cabinets online the pieces tight against the fence during this wood projects medicine cabinets online. I do a dry fit of all the pieces of the cabinet kedicine temporarily clamp it in place. The cabinet has ojline couple of permanent shelves in cabineys center, but above and below is an adjustable shelf.

I make out a template wood projects medicine cabinets online a piece of scrap plywood, drill it out, and transfer those marks to the side panels and drill them for adjustable shelf pins. Time for wood projects medicine cabinets online These are the permanent center shelves. I glue and screw everything in place. A countersink bit is used for all the holes so they can be plugged later. The perimeter pieces are medlcine around the center shelves.

Clamps hold these in place while I fasten them with glue and screws. Once the frame of the cabinets are assembled, I glue and screw the backer panel in place.

I make sure this is nice and secure because it is going to be fastened to the wall through this back panel. Now for the doors, I pull out a PVC sheet from my collection.

These are used as a shipping material and were pulled from the trash. So the door panels are made of 8 different pieces. The center pieces mimic the shelf structure on the inside, but run vertically. I clamp half of Wood Projects Medicine Cabinets Of China the door in place temporarily while I weave the small panels. I start with 4 pieces running vertically and then weave alternating mericine in.

Every few inches I use a dab qood hot glue to temporarily hold the outside vertical piece. I weave the other small panel and then the tricky part is installing lrojects rail on the other side. I do the same with the larger panel and then close up this cwbinets. Getting that piece on was a blast. I then do the same and weave the 4 panel. Once everything is together I take it apart again by pulling off the onlone and bottom piece to apply blue and then clamp them in place.

When the door panels are dry, I unclamp projectss and sand down Wood Projects Medicine Cabinets Yahoo each face to get the grime off of the reclaimed wood. Because of the hole in the center of the door, the groove that is used to hold the panels and promects is exposed. I planed ahead and cut a groove in the short pieces too so I could add trim and make this into a feature. I glue some mahogany pieces in place around the perimeter and use the clamp to squeeze them in tight.

Now I can plug the holes in the cabinet that were countersunk during assembly. I cut the plugs on my drill press using a plug hole cutter. To free the plugs projfcts the board I cut them off on the bandsaw. The plugs are installed by gluing them and hammering them in place. They are then cut flush with an oscillating saw and sanded smooth.

Now I just need to attach the door to the frame. I use some European hingesso I mark out the location to drill the projdcts. The pocket for the hinges is bored out with the drill press and forstner bit. I attach the plates medicien the hinges inside the cabinet and caibnets pop the hinges into place.

Once everything looks good, I pull the hardware off and prepare for finish. I wood projects medicine cabinets online tape off the woven panels to prevent getting any finish on them. I first apply wood projects medicine cabinets online coat of boiled linseed oil on everything then cabiinets that to dry for the night.

Then I use my concoction of mineral oil and beeswax to shine it up a bit. Wood projects medicine cabinets online is rubbed into the wood, let dry, and then buff to a subtle shine.

I drill 4 holes through the back of the cabinet to fasten them to wood projects medicine cabinets online wall.

I push the cabinet up against these and then mark through the holes onto the wall. The anchors are installed in the wall…. The door is then installed by popping the hinges back into place. Tested and approved! A whole bunch of strips!