Jet Variable Speed Mini Lathe Model Jml 1014vsi Usb,Craftsman Table Saw Blade,Wood Bowl Blanks For Turning Lyrics - PDF Review
Table Of Contents. Quick Links. Operating Instructions and Parts Manual. Table of Contents. Previous Page. Next Page. MVS Ph. For complete, up-to-date product information, check with your local WMH Tool Group distributor, or visit jettools. This warranty covers any defects in workmanship or materials subject to the exceptions stated below.
Page 4 runs up to feet, use a 14 AWG or larger gauge cord. For runs up to feet, use a 12 AWG or larger gauge cord. Runs over feet are not recommended. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.
This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. Page 6: Electrical Requirements Electrical Requirements In the event of a malfunction or breakdown, grounding provides a path of least jet variable speed mini lathe model jml-1014vsi usb for electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Page 7: Receiving Do not clean the lathe with anything other than a jet variable speed mini lathe model jml-1014vsi usb cloth or a mild solvent.
Use of heavy solvents, paint thinner, gasoline, etc. Page 8: Jet Variable Speed Mini Lathe Frame Assembly Assembly Mount the control box shown in Figure 1 to the headstock side of the lathe, by inserting the two screws through the hinge plate and into the threaded holes in the lathe body. If desired, the lathe can be bolted to a work table or stand by removing the jet variable speed mini lathe model jml-1014vsi usb feet and inserting screws through the holes in the base.
Turn counter- clockwise to retract tailstock spindle. Release to adjust with handwheel. Tailstock Lock C, Figure 2 - Locks tailstock in position on the bed. Release to move tailstock assembly closer to or farther from the headstock. Page jet variable speed mini lathe model jml-1014vsi usb Spur Center Figure 4 - locks into headstock and holds the Jet 1221 Variable Speed Midi Lathe Translation workpiece during spindle turning. Figure 4 Thoroughly clean the taper on the spur center and the inside of the headstock spindle before mounting the spur center.
Failure to do so may result in separation of the two and possible injury or tool damage. Used to steady cutting tool during spindle turning or face plate operations. Figure 8 Adjusting the Tool Rest Position the tool rest as close to the work piece as possible.
Page Variable Speed Control Variable Speed Control The variable speed control box contains the electrical connections to the motor, and has three external controls. Always set the speed control knob to its lowest setting before starting lathe. Never start a workpiece at maximum speed. Figure 9 Power Switch A, Figure 9 — Page Changing Spindle Speeds Figure 10 Changing Spindle Speeds The variable speeds of the lathe are controlled by the speed knob on the control box as well as the position of the belt on the pulleys.
Disconnect machine from the power source unplug. Page Belt Replacement Belt Replacement 1. Disconnect the machine from the power source unplug. Open the access doors at Jet Mini Wood Lathe Accessories 2020 the left side of the base Figure 10and at the back side of the headstock Figure Loosen the motor plate lock handle A, Figure Lift up on the motor plate handle B, Figure 12 to take tension off the belt. Page Indexer Operation Indexer Operation The index feature allows you to cut evenly spaced features in a workpiece while keeping the Lathe headstock spindle locked; for example, when cutting flutes on a spindle blank with a router, while the spindle blank is secured within the Lathe centers.
There are 24 index positions on the lathe. Page Parts List For JmlVsi To order parts or reach our service department, call between a. CSTMonday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
Index No. Page 18 Phillips Pan Head Machine Screw D Label. Speed Label. JET Label. JET Plaque. Motor Label. Control Panel Label Part No. Spur Center Center Point for Spur Center. Page 22 Live Center Head. Center Point for Live Center. Ball Bearing Live Center Shaft. Live Center Assembly not jet variable speed mini lathe model jml-1014vsi usb. Tailstock Spindle. This manual is also suitable for: Jwl vs Jwlvs.
Print page 1 Print document 24 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.
Triton Tra001 Review Us Word By Word Picture Dictionary Audio Mp4 Woodworking Gift Ideas For Him Live |
zZz
02.09.2020 at 16:33:21
KOR_ZABIT
02.09.2020 at 17:43:42
BERLIN
02.09.2020 at 10:20:54
AuReLiUs
02.09.2020 at 20:13:23
dsssssssss
02.09.2020 at 22:27:23