%!$ Easy Diy Woodworking Bench Plans For You #!@

dewalt-7770-radial-arm-saw-not Dewalt Manuals | ManualsLib

Oc:era t ion and Maintenance 4 Machine Controls. Models and have motors to you. Remove guard box, tip carton on end 3. Set machine containing motor by turning elevat- upright.

Re- move motor from box. Unpack guard box and hardware bag. Remove two screws from arm end- 6. Carefully slide the motor assembly cap, wipe arm tracks with clean cloth. Replace the endcap and tighten screws securely. Attach flat washers, lockwashers and nuts and tighten finger tight.

Assemble guide fence and spacer Insert bracket into the slot cessed side against blade. Dewalt 7770 radial arm saw not except front inner retaine r and provided in rear of cleats.

Hold the arbor nut securely with both inner ring per radiall Parts List dia- eyelet in place dewalt 7770 radial arm saw not turn the thumb wrenches left-hand threads. Place guard over blade tilting guard slightly to clear the arbor shaft.

Seat guard on motor so that the guard rides in the circular slot in the motor and the motor stud goes through the hole in the guard. Secure with the wingnut. Place the inner ring under the motor and hook it over the rear retainer and the front boss. Install the front inside retainer with the thumb- screw and tighten securely. Note that this step must be repeated in reverse order to gain access to the blade for removing it. Place the key in the endcap but do not press the ON button.

Securely fasten the table frame to the Accessory Cabinet, Leg Stand or a sturdy work bench using the holes provided.

Shim under the legs to get the table top approximately level in both directions. Read, understand and always practice the cautions and operating radiall contained within this manual. The tool is equipped with an or other qualified service organizations. Should you be approved three-conductor cord and three-prong grounding determined to make a repair yourself, remember that the type plug to fit the proper grounding type receptacle.

The Vintage Dewalt Radial Arm Saw Accessories In green colored wire is the "grounding" wire. Never con- green or green and yellow conductor in the cord is the nect this green wire to a "live" terminal. If you replace grounding wire. Never connect the green or green sad the plug on the power cord, be sure to connect the green yellow wire to a live terminal. Replace or repair damaged or worn cord immediately. If your unit is for use on less than volts, it has a plug like that shown in Figure A.

If it is for use on to The use of a separate 15 ampere circuit is recommended. Any such A. DO- Protect line with at least a 15 ampere time delay fuse. Read the owner's jot carefully. Learn its application and limitation, as well as the 2. DO- Be sure blade rotates clockwise when facing arbor.

DO- Be sure all cl amp handles and thumb screws are tight 2. Push handles back to tighten. If tool is equipped with three-prong Pull to loosen. If an adapter is used to accommodate a two-prong receptacle, the 4. DO- Be sure blade and arbor collars are clean and recessed side of collars are against blade.

Tighten arbor nut securely, adapter wire must be attached to a known ground. Never remove usin g both wrenches provided. Form habit 5. DO- Keep saw blade sharp and properly set.

DO- U se anti-kickback attachment on guard. Cluttered areas and benches invite 7. DO- Keep arm tracks and bearing surfaces clean and dry. Periodic cleaning with dry dewalt 7770 radial arm saw not is recommended. Don't use power tools 8. DO-Periodically recheck alignment. Keep work area well lighted.

DO-Remove bl ade but not arbor collars and nut when using rear shaft. Tighten nut securely. All vis tors should be kept a safe distance from work dewalt 7770 radial arm saw not. DO- Keep motor air slots clean and free of chips. DO- Dewalt 320 Radial Arm Saw Iso Remove switch gadial and store in a safe place to prevent switches, or by removing starter keys. It will do the job better and be safer at the rate for which it was dadial.

DO-Use lower guard at all times. Don't force tool or attachment to do a job it was not designed for. No loose clothing, gloves, neckties, voltage. Non-slip footwear is 2. DON'T-Operate unless all clamp handles are dewalt 7770 radial arm saw not. Wear protective xewalt covering to contain long hair.

Also use face or dust mask if 3. DON'T- Use blades of larger diameter th an recommended. Raddial it to just Serious injury could occur if the clear the workpiece when crosscutting. DON'T-Rip from wrong dewalt 7770 radial arm saw not observe caution tag on Keep your proper footing and balance at guard.

DON'T-Oil or grease arm tracks or motor. Keep tools sharp and clean for best performance. Follow instructions for lubricating and 7. DON'T-Wedge anything against fan to hold motor shaft. DON'T-Subject table top to variable humidity conditions keep away from dampness. Consult owner's 9. DON'T-Force cutting action. Stalling or dewqlt stalling of manual. Use of improper accessories may be hazardous. Make sure switch is off DON'T-Remove saw blade guard when boring.

DON;T -Remove arbor collars and nut Dewalt 1370 Radial Arm Saw Not when using rear Motors in these tools normally DON'T- Remove ground prong from plug. Never operate saw unless it is properly grounded. A guard or other part that is damaged should be properly repaired or replaced.

Your Saw Motor is equipped mot a manu dewalt 7770 radial arm saw not type overload protector. If the protector "trips" and stops the motor, take the Turn power off. Don't leave tool until it comes to a complete stop. Feed work into a blade or cutter against I. Press the saw "STOP" switch button and allow the motor the direction of rotation of the blade or cutter only.

Use clamps or vise to hold work when practical. It's safer than using your hand and dewalt 7770 radial arm saw not frees both hands 2. After mol or has cooled, the overload protector may be reset to operate tool.

If yOu do not hear an audible "click", the motor must be allowed to cool further before attempting the reset. The versatility of the radial-arm machine is due, in part, to its controls, and these are the keys to its successful operation.

I am looking for a replacement /4hp motor for my DeWalt 10" radial arm saw? Richard for model number / asked on Hello, Thank you for writing. and care of your new DeWalt Saw. These instructions in- clude operation. safety pre. cautions, preventive mainte. nance. maintenance and other pertinent data to assist you in assuring long life and dependable service from your saw. 10" SAFETY tool institute RADIAL ARM SAW NO. / TYPE 3 Bulletin No. Woodworking Radial Arm Saws; DEWALT ; See more models of this Type See more models for this Brand. DEWALT Model. Brand. DEWALT. Type. Woodworking Radial Arm Saws. Contact Sales Rep. The Original Saw Company 3rd Ave SE Britt, Iowa United States. HSO | Herramientas y Servicios Agustín de Vildosola No. Hermosillo.

Arb Roller Drawer Table Price Best Band Saw Blade For Stainless Steel Yellow Carving Tools Lino Outdoor Carpentry Projects