%!$ Easy Diy Woodworking Bench Plans For You #!@

dawn-number-9-woodworking-vise-app Dawn No. 9 Woodworking Vise | Hand Tools | Gumtree Australia Barossa Area - Tanunda |

I'm moving my workshop from the cellar into the garage to have more space. I built my own workbench and what's still missing, is a woodworking vise. There are several vise sets online, but I want to build my own one. In this Instructable you can follow all my steps and hopefully be able to build your own. I want to use a M16 threaded rod for the linear movement.

Therefore I need a nut or something threaded to interact with the rod. I decided to weld a M16 nut to a flat plate connector. The flat plate connecter has already some holes to fix this part to the workbench.

Unfortunately I don't have a welder Dawn Woodworking Vise Model so I asked my dad to do this job for me. I gave him the two parts and you can see what I got back in the second picture : He decided, that it would be better to use a thicker piece of metal for the base plat. So he used a thick old washer and drilled two holes in it. I'm glad he did the welding, but I think my idea with the base plate connector would have worked just as fine.

Remember to drill a hole into the plate big enough to let the rod pass through. I want to use a T-piece pipe to hold the threaded rod and a wooden rod later. So back to my dad and his welder.

To fix the rod, we added a small hole through the T-piece and the rod and insert a small bolt. Now you can turn the dawn number 9 woodworking vise app by turning the T-piece.

The washer we added is very important. It will later hold the jaw of the vise and will make it move when you want to open the vise. Both parts are finished. Let's try if everything fits together. Looks very good. The difficult part is done. Now comes some woodworking. Dawn number 9 woodworking vise app what we need next is a moveable jaw for the vise.

My dimensions are 40cm by 15cm, but you can adjust them to your needs. I use scrap wood I have laying around. I would use some kind of hard wood for the jaws, but unfortunately I don't have enough, but I use a little trick. The core consists of three pieces of roof batten made of spruce. It's too soft in my opinion. To reinforce the surface, I use an old piece of laminate I have left over from our master bedroom flooring.

The laminate is very strong and is just perfect for this job. I simply cut two pieces into the right dimensions. Now I got my laminate-spruce sandwich :. I glue all pieces together using wood glue. After everything is dry, I reinforce the structure by applying some counter-sinked screws on both sides.

Dawn number 9 woodworking vise app this is totally up to you. The glue should be enough I guess. They have a length of 50cm. You can adjust the length to your needs. I don't have a drill press yet, so I use a rack for my driller dawn number 9 woodworking vise app get the holes perpendicular to the surface.

The hole in the middle is dawn number 9 woodworking vise app the threaded rod and has to go right through the jaw. I add two more holes for the support pipes. These holes should not go right through. Therefore I use a forstner driller. I insert the copper pipes and mark the middle to the bottom side of the jaw. I use a metal drill to drill two small holes through the wood and the copper pipe.

I insert and counter-sink two screws to mount the pipes to the jaw. This time I need three holes which go right through the workbench. I use my rack to get everything in a right angle.

Dawn number 9 woodworking vise app finish the surface with a sander. Remember the washer, which we welded to the T-piece? Now you'll see its purpose. I need some kind of flange, which will connect the jaw to the rod, but still loose enough to allow rotation.

This allows the jaw to move with the rod while opening the vise. I use some scrap piece of laminate and mark a wide enough square in my vase 7cm time 7cm. I find the middle and cut out a round dent using a forstner bit the diameter dawn number 9 woodworking vise app be wider than the washer, the depth should be deeper than the thickness of the washer.

The dent will later house the washer and must not go right through the laminate. I use a second smaller forstner bit to cut right through the diameter should be smaller than the washer's and bigger the nut's diameter. I use a handsaw to cut the piece in half so I can mount it to the jaw. I use counter-sinked screws to fix the two flange pieces to dawn number 9 woodworking vise app jaw. Make sure that the rod can easily rotate.

We are almost finished here. I have to mount the washer and the nut piece to the back of my workbench jaw. Finally I can insert the copper pipes and the rod into the holes and screw in the threaded rod. You can add some lubricant to the thread. The last step is to build a handle. I use a 2cm wooden rod made of beech. I cut it in 40cm lengths, but feel free to adjust this to your needs. I use two rubber Dawn Number 9 Woodworking Vise Review doorstoppers for the ends. I use a screw and a washer for each to mount it to the handle.

This will avoid nasty bump accidents later on and also keeps the rod from falling through the T-piece. Congratulations, everything is done and dawn number 9 woodworking vise app are hopefully a proud owner of a new vise as well :D I hope you will enjoy building this.

Please let me know your experiences and improvements. Please put photos in the comments. Ok now let's get to business. I did some minor projects with the vise. The holding power is more than enough and I'm really happy with it.

I also used it to hold some smaller pieces for my router. It did a great job here, but there are some improvements I would do differently next time dawn number 9 woodworking vise app I will add later:.

Thank you Stish. Very nice and easy project for a beginner like me. I will make a few adjustments though with a wider thread bar and solid guide rails as mentioned in previous comments but your idea is great and i will definitely be adding this to my workshop! The only problem I have is you should have used hardwoods for maximum durability.

Some maple would not have been too costly. Over time you will find these things matter in a work bench. It really gets beat up and a soft wood will not endure as much abuse. You might enjoy this DIY quick-adjust mechanism by Pask, particularly with your fine for a vise threads. Reply 1 year ago. Nice project. The usual screw thread for a vise is a coarse pitch called acme thread.

It's also used on adjustable piano stools. Thx for the advice. I also found some one who build a vise from a base jack, which is used on scaffolding.

Yup, the difference is huge, here and in the wooden vise I built a lot of time is wasted since the vise jaw doesn't advance that much for each turn Question 1 year ago on Step 8. I'm curious why you chose hollow copper pipe for the horizontal sliding supports. Does the vise need to flex to work properly?

Answer 1 year ago.

Dawn underbench vise mm jaws Excellent working condition Collect from Tanunda Mob , Mophorn Wood Vise 9 Inch Woodworking Vise, Heavy-Duty Steel and Cast Iron Workbench Vise, Easy-to-operate Front Vise, Durable Woodworking Bench Vise for Home, Woodworking Studios, Teaching Equipment out of 5 stars Yost M9WW Rapid Acting Wood Working Vise, 9″. The Yost is a great woodworking vise for home as well as a professional woodworker’s use. This tool is constructed using rugged cast iron. One of its amazing features is the quick release mechanism that disengages the screw for a faster adjustment.

Wood Fired Oven Plans Pdf 5g Woodwork Basics Open Hardware Alliance Js Pumpkin Carving Kit Diy 90