%!$ Easy Diy Woodworking Bench Plans For You #!@

Printed in U. WEAR Learn specific its applipotential with three-prong plug, it should be radkal into a three-hole grounded receptacle.

If adapter is used to accommodate two-prong receptacle, the adapter wire must be attached to a known ground. Never remove third prong. The hazards. That recommended cause if the tool contacted. That 5. Always wear safety glasses or eye shields before commencing power tool operation.

We recommend Wide Vision Safety Mask for use over spectacles, or standard safety glasses. A guard or other part that is damaged should be properly repaired or replaced. TOOLS Don't AVOID accidents. Consult be kept is dusty. DON'T footing Keep tools sharp craftsman radial arm saw key 91 clean performance.

Follow instructions changing accessories. CLEAN areas and benche. It's safer than using your hand, frees both hands to operate tool. AVOID to get caught in moving is recommended for best Rubber-soled footing. Electrical Connections Operating Controls Basic Saw Operations Motor Trouble Shooting Chart Guarantee Repair Parts Basic Saw assembly Rear craftsmaan Table spacer Rip fence Front table Elevation crank assembly Knob assembly, pull Switch key Arbor wrench Lockwasher, Craftsman Radial Arm Saw Model 113 Jacket medium, ".

Nut, hex. Machine screw, pan-hd. Setscrew, eup-pt Machine screw, pan-hal. Mounting Your and preassembly Saw on a Workbench Mount on a Craftsman Power bench, in such a position that free to rotate, 4. Tool Base or a sturdy, flat the elevation crank Craftsman Radial Arm Saw Model 113 Key will be 3.

Installing Knob the Figure you Elevation are working on the saw. Crank Swivel and tighten Latch-Pin the preventing tracks. Figure on the carefully start and slide the carriage onto the radial-arm tracks. The assembly must be held parallel with the arm so that all four of the assembly bearings will smoothly slide onto the two arm tracks, thus 2 a.

Install the elevation crank and on the flat portion of the shaft. Assembly a. Rotate tbe elevation crank clockwise craftsman radial arm saw key 91 turns and remove the shipping block from between the carriage and the radial arrn.

Remove the carriage stop screw. Iockwasher and warning tag. This cord must remain craftsman radial arm saw key 91 whenever Installing the Motor and Carriage Radial Arm Sae 2 and 3 strain on the bearings and stop screw and Iockwasher.

Unless this is done carriage can rol! Remove the two shipping screws from bottom of motor, and discard. Leaving these in would limit depth of cut. Check the cord in the arm cord clip to make sure there is 30 inches length of cord between this clip and the cord clip on the yoke. Remove the carriage lock right-hand carriage cover. Tighten the screws lightly -- the indicator will be adjusted, later c, Reinstall the carriage knob, 4 then remove the cover and knob.

Similarly attach the remaining keh indicator to left-hand carriage cover, then reinstall this cover Note that there is no knob on the left side; only [he cever need be removed and reinstalled. Loosen the guard-clamp assembly.

Place the arbor wrench screw and remove on the shaft wrench on the hex portion the saw blade. The motor shaft has left-hand threads.

Craftsmah e. Remove collar. Place the saw blade, nut, collars, Craftsman Radial Arm Saw Key In and guard assembty where they will be out of your way during the following adjustment steps. If the table supportsand the table - are not precisely squared with the saw-blade travel in all operating positions, the blade may not produce clean, uniform cuts.

Removing shaft nut, Figures 4, 5 and 6 Loosen the handle up bevel lock knob and b. Swivel the motor counterclockwise of the shaft is pointing straight lock knob. Loosen them just enough for the support to move up or down when tapped with a rubber mallet.

Lay the handle end of the arbor wrench on the mounting support and, while holding the wrench flat on the support, carefully am the elevation crank to lower the motor until the motor shaft end just touches the wrench surface.

You should be able to 8 slide the resistance. Do qot change the setting until you have satisfactorily completed the adjustment of both table mounting supports. Repeat the directly support above the front, attaching screw.

Tighten cgaftsman two through "h" to make certain tha fits between the motor-shaft en channel in an identical manner a front. Adjust the right-hand same manner, without tion setting. It is upside down when the face in which the screw holes are counterbored is at bottom.

Drive the T-nut furnished with loose parts into the smaller of these two center holes. Turn the front table top side up and place craftsman radial arm saw key 91 on the table supports, locating it so that the six screw holes near the board sides are aligned with their corresponding holes in the two supports.

In the larger of the two center holes place one 17! Move the carriage to its extreme tighten the carriage lock knob. Lay the rear table board on edge across the front table to serve as aaw straightedge. Sight under this straightedge to determine whether the front table board is high or low at its center. If the center do not tighten it.

In the the T-nut underneathrear position, craftsman radial arm saw key 91 set-screw. Install one 1! The board should be craftsman radial arm saw key 91 against the supports, but not held too tightly to be moved by tapping it firmly with a rubber mallet.

Squaring the Crosscut Travel Figures 16 through 23 Figure 19 a. Loosen the carriage lock knob, move the carriage to the approximate center of craftsman radial arm saw key 91 radial arm, then retighten the lock knob. Install 1 the saw blade, as follows: Place on the motor shaft, in this order: 1 One of the 20 Radial Arm Saw Key two blade collars, flat face out; 2 The blade, with when The blade; 2 the teeth pointing in a clockwise direction you are facing saw-blade end of motor; 3 remaining blade collar, flat face against and 4 The shaft nut.

Tighten the shaft nut as shown in Figure Do not craftsman radial arm saw key 91 or keyy the arm. Tap the arm latch solidly with the palm of your hand to seat the arm lock pin firmly.

Craftsman radial arm saw key 91 turning the elevation crank counterclockwise, lower the blade until it just clears the front table.

Figure 21 Figure 23 22 Now slowly move the carriage outward along the radial arm. Ar tooth you have marked should just touch the rarial leg of the square at all points. If it does not, make the following adjustments: 1 If your marked tooth moves into the square as the carriage is moved outward, tap the left-front edge of the table with a rubber mallet until you can perform step "g" correctly. Also refer to page 20, craftsman radial arm saw key 91 Trouble Shooting Section.

Tighten the screws. Position the rip fence, spacer board and rear board behind the front table board, as shown. Install the two table them at the rear of securely. This should be tacked in place for easy replacement.